Nissan Qashqai J11. Manual — part 144
LU-36
< PERIODIC MAINTENANCE >
[K9K]
ENGINE OIL
Draining
INFOID:0000000010284208
WARNING:
• Be careful not to burn yourself, as the engine oil is hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer: try to avoid direct skin
contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1.
Put vehicle horizontally.
2.
Warm up engine, and check for oil leakage from engine components.
3.
Stop engine and wait for 10 minutes.
4.
Loosen oil filler cap.
5.
Remove drain plug and then drain engine oil.
Refilling
INFOID:0000000010284209
1.
Refill with new engine oil.
• Refer to
MA-59, "Fluids and Lubricants"
.
• The refill capacity depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to the determine when the proper amount
of oil is in the engine.
CAUTION:
• Be sure to clean drain plug and install with new washer.
• The refill capacity depends on the oil temperature and drain time. Use these specifications for ref-
erence only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
2.
Warm up engine and check area around drain plug and oil filter for oil leakage.
3.
Stop engine and wait for 10 minutes.
4.
Check oil level.
Oil capacity (Approximate)
: Refer to
"Periodical Maintenance Specification"
.
MBIB0548E
OIL FILTER
LU-37
< PERIODIC MAINTENANCE >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL FILTER
Replacement
INFOID:0000000010284210
1.
Using an oil filter wrench [SST: KV113C0010 (Mot. 1329)],
remove oil filter.
CAUTION:
• Be careful not to get burned when the engine and engine
oil are hot.
• When removing, prepare a shop cloth to absorb any oil
leakage or spillage.
• Do not allow engine oil to adhere to the drive belts.
• Completely wipe off any oil that adhere to the engine and
the vehicle.
2.
Remove foreign materials adhering to the oil filter installation
surface.
3.
Install oil filter bracket to oil cooler.
CAUTION:
Install oil filter bracket, positioning lug in the hole of oil cooler.
4.
Apply engine oil to the oil seal contact surface of the new oil fil-
ter.
5.
Install the oil filter until it comes into contact with the oil seal on
the engine bracket.
6.
Using an oil filter wrench [SST: KV113C0010 (Mot. 1329)],
tighten oil filter.
7.
After warming up the engine, check for engine oil leakage.
8.
Check oil level and add engine oil. Refer to
.
Inspection
INFOID:0000000010284211
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
: 14 N·m (1.4 kg-m, 10 ft-lb)
MBIB0551E
SMA010
LU-38
< REMOVAL AND INSTALLATION >
[K9K]
OIL FILTER BRACKET
REMOVAL AND INSTALLATION
OIL FILTER BRACKET
Exploded View
INFOID:0000000010284212
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010284213
REMOVAL
CAUTION:
• Be careful not to get burned when the engine and engine oil are hot.
• When removing, prepare a shop cloth to absorb any oil leakage or spillage.
• Do not allow engine oil to adhere to the drive belts.
• Completely wipe off any oil that adhere to the engine and the vehicle.
1.
Remove oil filter. Refer to
2.
Remove oil filter bracket.
INSTALLATION
Install in the reverse order of removal.
1.
O-ring
2.
Oil filter bracket
3.
Oil pressure switch
4.
Oil filter
5.
O-ring
6.
Connecting bolt
A.
To oil cooler
E1BIA0012GB
OIL COOLER
LU-39
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL COOLER
Exploded View
INFOID:0000000010284214
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010284215
CAUTION:
• Be careful not to get burned when the engine and engine oil are hot.
• When removing, prepare a shop cloth to absorb any oil leakage or spillage.
• Completely wipe off any oil that adhere to the engine and the vehicle.
REMOVAL
1.
Drain engine coolant. Refer to
.
CAUTION:
Perform when engine is cold.
2.
Remove oil filter and oil filter bracket. Refer to
LU-38, "Removal and Installation"
.
3.
Remove water hoses from oil cooler.
4.
Remove oil cooler.
INSTALLATION
Installation is in reverse order of removal.
• Replace the O-ring of the oil cooler.
• Confirm that no foreign objects are adhering to the installation planes of the oil cooler and block.
1.
Cylinder block
2.
Water pipe
3.
O-ring
4.
O-ring
5.
O-ring
6.
Oil cooler
7.
Connecting stud
8.
O-ring
9.
Oil filter bracket
10. Oil pressure switch
11.
Oil filter
12. O-ring
13. Connecting bolt
A.
To radiator lower hose
B.
To water pump
E1BIA0011GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст