Nissan Qashqai J11. Manual — part 313
P014C, P014D A/F SENSOR 1
ECM-229
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
ECM
N
P
O
10.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to
.
CAUTION:
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
ECM-230
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P0171 FUEL INJECTION SYSTEM FUNCTION
P0171 FUEL INJECTION SYSTEM FUNCTION
DTC Description
INFOID:0000000010702938
DTC DETECTION LOGIC
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual mixture ratio can be brought closely to the
theoretical mixture ratio based on the mixture ratio feedback signal from A/F sensor 1. The ECM calculatesthe
necessary compensation to correct the offset between the actual and the theoretical ratios.
In case the amount of the compensation value is extremely large (the actual mixture ratio is too lean), the
ECM judges the condition as the fuel injection system malfunction and illuminates the MIL (2 trip detection
logic).
POSSIBLE CAUSE
• Intake air leakage
• A/F sensor 1
• Fuel injector
• Exhaust gas leakage
• Incorrect fuel pressure
• Lack of fuel
• Mass air flow sensor
• Incorrect PCV hose connection
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
Sensor
Input signal to ECM
ECM function
Actuator
A/F sensor 1
Density of oxygen in exhaust
gas (Mixture ratio feedback
signal)
Fuel injection control
Fuel injector
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0171
FUEL SYS-LEAN-B1
(System too lean bank 1)
• Fuel injection system does not operate properly.
• The amount of mixture ratio compensation is too large. (The mixture ratio
is too lean.)
Engine operating condition in fail-safe mode
Fail safe mode
Vehicle behavior
Traveling con-
trol mode
Accelerator an-
gle variation
control
ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Combustion
control mode
Stratified charge
combustion
control at start-
ing
No stratified charge combustion at starting (cold start).
Idle speed con-
trol
Stops feedback control of idle speed and controls with specified speed.
Recovery speed
control at decel-
erating
Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral con-
trol
Stops idle neutral control.
P0171 FUEL INJECTION SYSTEM FUNCTION
ECM-231
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
ECM
N
P
O
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
1.
Clear the mixture ratio self-learning value. Refer to
.
2.
Start engine.
Is it difficult to start engine?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
RESTART ENGINE
If it is difficult to start engine, the fuel injection system has a malfunction, too.
Crank engine while depressing accelerator pedal.
Does engine start?
YES
>> Proceed to
ECM-231, "Diagnosis Procedure"
.
NO
>> Check exhaust and intake air leak visually.
4.
PERFORM DTC CONFIRMATION PROCEDURE-II
1.
Start engine and let it idle for at least 10 minutes.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
ECM-231, "Diagnosis Procedure"
.
NO
>> GO TO 5.
5.
PERFORM DTC CONFIRMATION PROCEDURE-III
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Start engine and drive the vehicle under the similar conditions to (1st trip) Freeze Frame Data for 10 min-
utes. Refer to the table below.
Hold the accelerator pedal as steady as possible.
The similar conditions to (1st trip) Freeze Frame Data means the vehicle operation that the following con-
ditions should be satisfied at the same time.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
ECM-231, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010702939
1.
CHECK EXHAUST GAS LEAKAGE
1.
Start engine and run it at idle.
Engine speed
Engine speed in the freeze frame data
±
400 rpm
Vehicle speed
Vehicle speed in the freeze frame data
±
10 km/h (6 MPH)
Engine coolant temperature (T) condition
When the freeze frame data shows lower than 70
°
C (158
°
F),
T should be lower than 70
°
C (158
°
F).
When the freeze frame data shows higher than or equal to 70
°
C (158
°
F),
T should be higher than or equal to 70
°
C (158
°
F).
ECM-232
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P0171 FUEL INJECTION SYSTEM FUNCTION
2.
Listen for an exhaust gas leakage before three way catalyst (manifold).
Is exhaust gas leakage detected?
YES
>> Repair or replace malfunctioning part.
NO
>> GO TO 2.
2.
CHECK FOR INTAKE AIR LEAKAGE
1.
Listen for an intake air leakage after the mass air flow sensor.
2.
Check PCV hose connection.
Is intake air leakage detected?
YES
>> Repair or replace malfunctioning part.
NO
>> GO TO 3.
3.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect corresponding A/F sensor 1 harness connector.
3.
Disconnect ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
5.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
6.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning part.
4.
CHECK FUEL PRESSURE
PBIB1216E
+
−
Continuity
A/F sensor 1
ECM
Connector
Terminal
Connector
Terminal
F74
1
F16
64
Existed
2
72
+
Ground
Continuity
A/F sensor 1
Connector
Terminal
F74
1
Ground
Not existed
2
+
Ground
Continuity
ECM
Connector
Terminal
F16
64
Ground
Not existed
72
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст