Nissan Qashqai J11. Manual — part 1671
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
MIR-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
Component Function Check
INFOID:0000000011405237
1.
CHECK FUNCTION
1.
Turn the door mirror open/close switch to “AUTO”.
2.
Turn ignition switch ON.
3.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
4.
Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.
5.
Touch “On” check that it works normally.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000011405238
1.
CHECK DOOR MIRROR OPEN RELAY AND DOOR MIRROR CLOSE RELAY POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror open relay and door mirror close relay connector.
3.
Check voltage between door mirror open relay and door mirror close relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (#28)
• Harness for open or short between door mirror remote control switch harness connector and battery termi-
nal.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between door mirror open relay and door mirror close relay harness connector and BCM
harness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(
−
)
Voltage (V)
(Approx.)
Door mirror open/close relay
Connector
Terminal
M100
1
Ground
Battery voltage
M101
1
5
Door mirror open/close relay
BCM
Continuity
Connector
Terminal
Connector
Terminal
M100
2
M70
58
Existed
M101
BCM
Ground
Continuity
Connector
Terminal
M70
58
Not existed
MIR-60
< DTC/CIRCUIT DIAGNOSIS >
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK OPEN/CLOSE MOTOR GROUND CIRCUIT
1.
Disconnect door mirror remote control switch connector.
2.
Check continuity between door mirror remote control switch harness connector and door mirror open relay
harness connector.
3.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK DOOR MIRROR OPEN RELAY
Check door mirror open relay.
Refer to
MIR-61, "Component Inspection (Door Mirror Open Relay)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness or connector.
6.
CHECK DOOR MIRROR CLOSE RELAY
Check door mirror close relay.
Refer to
MIR-61, "Component Inspection (Door Mirror Close Relay)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness or connector.
7.
CHECK BCM FUNCTION
1.
Turn the door mirror open/close switch to AUTO.
2.
Connect door mirror remote control switch connector, door mirror open relay, door mirror close relay and
BCM connector.
3.
Turn ignition switch ON.
4.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
5.
Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.
6.
Touch “On” and check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
door mirror remote control switch
Door mirror open relay
Continuity
Connector
Terminal
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
7
M100
5
Existed
door mirror remote control switch
Ground
Continuity
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
7
Not existed
(+)
(
−
)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
58
Ground
RETRACTABLE
MIRROR
ON
0
OFF
Battery voltage
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
MIR-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection (Door Mirror Open Relay)
INFOID:0000000011405239
1.
CHECK DOOR MIRROR OPEN RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror open relay.
3.
Check the continuity between door mirror open relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror open relay.
Component Inspection (Door Mirror Close Relay)
INFOID:0000000011405240
1.
CHECK DOOR MIRROR OPEN/CLOSE RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror close relay.
3.
Check the continuity between door mirror close relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror close relay.
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
MIR-62
< SYMPTOM DIAGNOSIS >
ELECTRIC FOLDABLE DOOR MIRROR DOES NOT OPERATE
SYMPTOM DIAGNOSIS
ELECTRIC FOLDABLE DOOR MIRROR DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000011378323
1.
CHECK DOOR MIRROR (OPEN/CLOSE MOTOR) CIRCUIT
Check door mirror (open/close motor) circuit.
Refer to
MIR-54, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст