Nissan Qashqai J11. Manual — part 1670
DOOR MIRROR (OPEN/CLOSE MOTOR)
MIR-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK HARNESS CONTINUITY-1
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch harness connector and door mirror open/
close relay harness connector.
4.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace harness.
6.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Connect door mirror open relay and door mirror close relay connector.
3.
Disconnect door mirror (driver side) connector and door mirror (passenger side) connector.
4.
Turn ignition switch ON.
5.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror open/close relay
Connector
Terminal
M100
4
Ground
Door mirror remote
control switch
(open/close switch)
Auto
12
Other than above
0
M101
Close
12
Other than above
0
door mirror remote control switch
Door mirror open/close relay
Continuity
Connector
Terminal
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
5
M100
4
Existed
7
M101
door mirror remote control switch
Ground
Continuity
Connector
Terminal
Not existed
D6 (LHD models)
D36 (RHD models)
5
7
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror
Connector
Terminal
D27 (LHD models)
D16 (RHD models)
3
Ground
Door mirror remote
control switch
(open/close switch)
Auto
12
Close
0
11
Auto
0
Close
12
D3 (LHD models)
D40 (RHD models)
3
Auto
12
Close
0
11
Auto
0
Close
12
MIR-56
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR (OPEN/CLOSE MOTOR)
YES
>> GO TO 8.
NO
>> GO TO 7.
7.
CHECK HARNESS CONTINUITY-2
1.
Turn ignition switch OFF.
2.
Disconnect door mirror open relay connector and door mirror close relay connector.
3.
Check continuity between door mirror harness connector and door mirror open relay and door mirror close
relay harness connector.
4.
Check continuity between door mirror harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK DOOR MIRROR OPEN RELAY
Check door mirror open relay.
Refer to
MIR-57, "Component Inspection (Door Mirror Open Relay)"
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace door mirror open relay.
9.
CHECK DOOR MIRROR CLOSE RELAY
Check door mirror close relay.
Refer to
MIR-57, "Component Inspection (Door Mirror Close Relay)"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace door mirror close relay.
10.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH
Check door mirror remote control switch (open/close switch).
Refer to
MIR-57, "Component Inspection (Door Mirror Remote Control Switch)"
.
Is the inspection result normal?
YES
>> Replace door mirror open/close motor.
NO
>> Replace door mirror remote control switch.
11.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
door mirror
Door mirror open/close relay
Continuity
Connector
Terminal
Connector
Terminal
D27 (LHD models)
D16 (RHD models)
3
M100
3
Existed
11
M101
D3 (LHD models)
D40 (RHD models)
3
M100
11
M101
door mirror
Ground
Continuity
Connector
Terminal
Not existed
D27 (LHD models)
D16 (RHD models)
3
11
D3 (LHD models)
D40 (RHD models)
3
11
DOOR MIRROR (OPEN/CLOSE MOTOR)
MIR-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Component Inspection (Door Mirror Remote Control Switch)
INFOID:0000000011405234
1.
CHECK OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.
Component Inspection (Door Mirror Open Relay)
INFOID:0000000011405235
1.
CHECK DOOR MIRROR OPEN RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror open relay.
3.
Check the continuity between door mirror open relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror open relay.
Component Inspection (Door Mirror Close Relay)
INFOID:0000000011405236
1.
CHECK DOOR MIRROR OPEN/CLOSE RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror close relay.
3.
Check the continuity between door mirror close relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
Door mirror remote control switch
Condition
Continuity
Terminal
15
5
Open/close switch
AUTO
Existed
10
7
15
7
CLOSE
10
5
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
MIR-58
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR (OPEN/CLOSE MOTOR)
NO
>> Replace door mirror close relay.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст