Nissan Qashqai J11. Manual — part 27
OIL PAN (LOWER)
EM-47
< REMOVAL AND INSTALLATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Insert seal cutter [SST: KV10111100] (A) between oil pan (upper)
and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• Never insert a screwdriver. This damages the mating sur-
faces.
c.
Slide the seal cutter [SST: KV10111100] by tapping on the side
of tool with a hammer.
d.
Remove oil pan (lower).
INSTALLATION
1.
Install oil pan (lower) as follows:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off old liquid gasket.
b.
Apply a continuous bead of liquid gasket (B) with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
: Engine front
E1BIA1041ZZ
JPBIA0276ZZ
JPBIA4745ZZ
a
: 7.5 - 9.5 mm (0.295 - 0.374 in)
c
:
φ
4.0 - 5.0 mm (0.157 - 0.197 in)
1
: Oil pan (lower)
: Engine outside
E1BIA1040ZZ
EM-48
< REMOVAL AND INSTALLATION >
[HRA2DDT]
OIL PAN (LOWER)
c.
Tighten bolts in numerical order as shown in the figure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
.
3.
Install in the reverse order of removal after this step.
NOTE:
Wait at last 30 minutes after oil pan (lower) is installed before pouring engine oil.
Inspection
INFOID:0000000010282225
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
: Engine front
E1BIA1041ZZ
IGNITION COIL, SPARK PLUG AND ROCKER COVER
EM-49
< REMOVAL AND INSTALLATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL, SPARK PLUG AND ROCKER COVER
Exploded View
INFOID:0000000010282226
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010282227
REMOVAL
1.
Camshaft position sensor (EXH)
2.
Camshaft position sensor (INT)
3.
Rocker cover
4.
Rocker cover gasket
5.
Dowel pin
6.
Camshaft (EXH)
7.
Camshaft (INT)
8.
Cylinder head
9.
Engine slinger
10.
Spark plug
11.
Ignition coil
E1BIA1014GB
EM-50
< REMOVAL AND INSTALLATION >
[HRA2DDT]
IGNITION COIL, SPARK PLUG AND ROCKER COVER
1.
Remove brake booster hose (1).
2.
Remove air inlet hose and electric blow off valve. Refer to
EM-27, "Removal and Installation"
.
3.
Remove ignition coil.
CAUTION:
• Never drop or shock ignition coil.
• Never disassemble ignition coil.
4.
Remove spark plug. Refer to
EM-20, "Removal and Installation"
5.
Remove camshaft position sensor (INT and EXH). Refer to
.
6.
Remove PCV hose from rocker cover. Refer to
7.
Remove high pressure fuel pump. Refer to
EM-38, "Removal and Installation"
.
8.
Remove turbocharger heat shield.
9.
Disconnect and unclip A/F sensors harness.
10. Remove rocker cover.
• Loosen bolts in reverse order as shown in the figure.
NOTE:
Rocker cover bolts are not same, mark their positions.
11. Remove rocker cover gasket from rocker cover.
12. Use scraper to remove all traces of liquid gasket from cylinder head and front cover.
CAUTION:
Never scratch or damage the mating surface when cleaning off old liquid gasket.
INSTALLATION
1.
Rocker cover with the following procedure:
E1BIA1035ZZ
E1BIA1030ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст