Nissan Qashqai J11. Manual — part 2173
DAS-106
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
Change the magnification of print to 250 mm (9.84 in)
×
250 mm (9.84 in) and print the target mark sample.
JSOIA0633ZZ
DAS
ACTION TEST
DAS-107
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ACTION TEST
LDW
LDW : Description
INFOID:0000000010416827
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Lane Departure Warning"
.
LDW : Inspection Procedure
INFOID:0000000010416828
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Lane Departure Warning"
.
1.
CHECK LDW SYSTEM SETTING
1.
Start the engine.
2.
Check that the LDW system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR LDW
1.
Enable the setting of the LDW system on the vehicle information display.
2.
Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation
Action
LDW ON indi-
cator
Indication on the combination
meter
Buzzer
Less than
Approx. 55
km/h (34
MPH)
Close to lane marker
No action
ON
White
OFF
JSOIA1422ZZ
DAS-108
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 55 km/h (34 MPH). Refer to
DAS-15, "LDW : System Description"
>> Inspection End.
BSW
BSW : Description
INFOID:0000000010416829
• Perform action test to verify the customer
′
s concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for BSW: Refer to
DAS-17, "BSW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Blind Spot Warning"
BSW : Inspection Procedure
INFOID:0000000010416830
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for BSW: Refer to
DAS-17, "BSW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Blind Spot Warning"
1.
CHECK BSW SYSTEM SETTING
1.
Start the engine.
2.
Check that the BSW system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR BSW
1.
Enable the setting of the BSW system on the vehicle information display.
2.
Check the BSW operation according to the following table.
Approx. 60
km/h (37
MPH) or
more
Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks
ON
OFF (orange) Blink
Short contin-
uous beeps
• Close to lane marker
• Turn signal ON (Deviate
side)
No action
ON
White
OFF
Vehicle condition/ Driver's operation
Action
LDW ON indi-
cator
Indication on the combination
meter
Buzzer
JSOIA1367ZZ
JSOIA1422ZZ
DAS
ACTION TEST
DAS-109
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Vehicle condition/Driver
′
s operation
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 29 km/h (18 MPH). Refer to
DAS-17, "BSW : System Description"
.
>> Inspection End.
MOD
MOD : Description
INFOID:0000000010416831
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for MOD: Refer to
DAS-22, "MOD : System Description"
MOD : Inspection Procedure
INFOID:0000000010416832
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for MOD: Refer to
DAS-22, "MOD : System Description"
1.
CHECK MOD SYSTEM SETTING
1.
Start the engine.
2.
Check that the MOD system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
Warning
systems
ON
indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Turn signal
condition
Status of vehi-
cle detection
within detec-
tion area
Indication on the combination
meter
Buzzer
ON
Less than Ap-
prox. 29 km/h
(18 MPH)
—
—
OFF
OFF
Approx. 32
km/h (20
MPH) or more
—
Vehicle is ab-
sent
OFF
OFF
OFF
Vehicle is de-
tected
ON
OFF
ON (vehicle
detected di-
rection)
Before turn
signal oper-
ates vehicle is
detected
Blink
Short continuous beeps
Vehicle is de-
tected after
turn signal op-
erates
Blink
OFF
JSOIA0251GB
JSOIA0252GB
JSOIA0251GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст