Nissan Qashqai J11. Manual — part 2174
DAS-110
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
>> GO TO 2.
2.
ACTION TEST FOR MOD
1.
Enable the setting of the MOD system on the vehicle information display.
2.
Turn warning systems switch ON (warning systems ON indicator is ON).
3.
Check the MOD operation according to the following table.
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle reaches a
higher speed. Refer to
DAS-22, "MOD : System Description"
.
>> Inspection End.
Vehicle condition/ Driver's operation
Vehicle response
Moving Object De-
tection ON indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Status of vehicle detection
within detection area
Indication on the Moving Object Detection
indicator
Buzzer
OFF
—
—
OFF
OFF
Blue
Less than approx.
8 km/h (5 MPH)
Vehicle is detected
ON
ON
Approx. 8 km/h (5
MPH) or more
Vehicle is absent
ON
OFF
Vehicle is detected
ON
OFF
Vehicle is not detected
ON
OFF
DAS
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
DAS-111
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Description
INFOID:0000000010416835
Vehicle specification needs to be written with CONSULT because it is not written after replacing around view
monitor control unit.
Configuration has three functions as follows:
CAUTION:
• When replacing around view monitor control unit, you must perform “Select Saved Data List” or
"After Replace ECU" with CONSULT.
• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new around view monitor
control unit.
Work Procedure
INFOID:0000000010416836
1.
WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of around view monitor control unit.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “SAVED DATA LIST”
CONSULT
Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select
applicable file from the “Save Data List” and press “Confirm”.
>> Work End.
3.
PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”
CONSULT
1.
Select “After Replace ECU” or “Manual Configuration”.
2.
Identify the correct model and configuration list. Refer to
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
4.
Select “Next”.
CAUTION:
Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated con-
figuration of brand new around view monitor control unit is same as the desirable configuration. If
not, configuration which is set automatically by selecting vehicle model can not be memorized.
5.
When "Completed", select "End".
>> GO TO 4.
4.
OPERATION CHECK
Function
Description
"Before Replace ECU"
• Reads the vehicle configuration of current around view monitor control unit.
• Saves the read vehicle configuration.
"After Replace ECU"
Writes the vehicle configuration with manual selection.
"Select Saved Data List"
Writes the vehicle configuration with saved data.
DAS-112
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Confirm that each function controlled by around view monitor control unit operates normally.
>> Work End.
Configuration List
INFOID:0000000010416837
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
⇔
: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
HANDLE POSITION
RHD
⇔
LHD
—
TRANSMISSION
A/T
⇔
M/T
—
TIRE SIZE
TYPE 1
⇔
TYPE 3
• TYPE 1: 17 inch
• TYPE 3: 19 inch
4WD/2WD
4WD
⇔
2WD
—
SONAR
WITH
⇔
WITHOUT
• WITH 1: With sonar
• WITHOUT: Without sonar
LDW FUNCTION
WITH
⇔
WITHOUT
• WITH 1: With LDW function
• WITHOUT: Without LDW function
DAS
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
DAS-113
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
Description
INFOID:0000000010416838
Adjust the center position of the predictive course line of the rear view monitor if it is shifted.
Work Procedure
INFOID:0000000010416839
1.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст