Nissan Qashqai J11. Manual — part 1312
REMOTE KEYLESS ENTRY SYSTEM
DLK-517
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000010435123
System Description
INFOID:0000000010435124
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp
at the same time as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.
OPERATION AREA
To ensure that the keyfob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.
ANTI-HIJACK FUNCTION
• When an LOCK signal is transmitted from keyfob, all doors are locked.
• When an UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change anti-hijack mode.
With CONSULT
Anti-hijack mode can be set to ON or OFF using CONSULT.
Refer to
DLK-521, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 4)"
Without CONSULT
• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 5 sec-
onds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
HAZARD REMINDER FUNCTION
Operation Description
JMKIB3324GB
Remote controller operation
Operation condition
Lock
• Key switch is off
• All doors are closed
Unlock
Key switch is off
OFF
→
ON
: 1 blinks
ON
→
OFF
: 3 blink
DLK-518
< SYSTEM DESCRIPTION >
[TYPE 4]
REMOTE KEYLESS ENTRY SYSTEM
When doors are locked or unlocked by keyfob button operation, BCM blinks hazard warning lamps as a
reminder.
AUTO DOOR LOCK FUNCTION
After door is unlocked by keyfob button operation and if 30 seconds or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
522, "MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)"
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock/unlock state, refer to
CONTROL SYSTEM : System Description"
Door lock operation
(With keyfob button)
Hazard warning lamp blink
Lock
Once
Unlock (all door unlock)
Twice
Unlock (anti-hijack operation)
Twice (quick)
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Key switch is ON
BACK DOOR OPENER SYSTEM
DLK-519
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SYSTEM
System Description
INFOID:0000000010479511
SYSTEM DIAGRAM
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• All doors are unlocked.
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-520
< SYSTEM DESCRIPTION >
[TYPE 4]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010435125
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but is not used.
DOOR LOCK
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Manual A/C
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
—
IMMU*
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
—
THEFT ALM*
×
×
×
—
RETAINED PWR*
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст