Nissan Qashqai J11. Manual — part 57
FUEL INJECTOR AND FUEL TUBE
EM-167
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Install an injector seal drift set [SST: KV101197S0 (—)] (A) to
fuel injector
.
b.
Set seal ring
to injector seal drift set [SST: KV101197S0 (—)]
.
c.
Straightly insert seal ring
, which is set in step 2, to fuel injec-
tor as shown in the figure and install.
CAUTION:
Be careful that seal ring does not exceed the groove portion
of fuel injector.
d.
Insert injector seal drift set [SST: KV101197S0 (—)] (A) to injec-
tor and rotate clockwise and counterclockwise by 90
°
while
pressing seal ring to fit it.
NOTE:
Compress seal ring, because this operation is for rectifying
stretch of seal ring caused by installation and for preventing
sticking when inserting injector into cylinder head.
2.
Install O-ring and backup ring to fuel injector. When handing new O-ring and backup ring, paying attention
to the following caution items:
CAUTION:
• Do not reuse O-ring.
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly
into fuel tube.
JPBIA4386ZZ
JSBIA0348ZZ
JSBIA0350ZZ
JSBIA0351ZZ
EM-168
< REMOVAL AND INSTALLATION >
[MR20DD]
FUEL INJECTOR AND FUEL TUBE
• Insert new O-ring straight into fuel rail. Never decenter or twist it.
• Always install the back up ring
in the right direction as
instructed.
3.
Install fuel injector
to fuel rail
as per the following:
a.
Install fuel injector holder
to fuel injector.
CAUTION:
• Never reuse fuel injector holder. Replace it with a new
one.
• Be careful to keep fuel injector holder from interfering
with O-ring. If interference occurs, replace O-ring.
b.
Insert fuel injector into fuel rail with fuel injector holder attached.
• Insert it while matching it to the axial center.
• Insert so that protrusion
of fuel injector is aligned to cutout
.
c.
Check that installation is complete by checking that fuel injector
does not rotate or come off.
• Check that protrusions of fuel injectors and fuel rail are aligned
with cutouts of clips after installation.
4.
Install fuel rail and fuel injector assembly to cylinder head.
• Tighten mounting bolts and nuts in two steps in numerical
order as shown in the figure.
5.
Connect injector harness connector.
6.
Install fuel pressure sensor, if removed.
7.
Install fuel rail insulator.
CAUTION:
• As covering part of fuel tube connector at the back end of common rail can easily move because
of its shape, do not remove it before installation.
• Install the insulator so that it is placed under lower side of intake manifold flange.
8.
Install in the reverse order of removal after this step.
JPBIA3864ZZ
: O-ring (blue)
: Backup ring
JPBIA4387ZZ
: Engine front
1st step
: 10.0 N·m (1.0 kg-m, 89 in-lb)
2nd step
: 20.5 N·m (2.1 kg-m, 15 ft-lb)
JPBIA4388ZZ
FUEL INJECTOR AND FUEL TUBE
EM-169
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Inspection
INFOID:0000000010715486
INSPECTION AFTER INSTALLATION
Check on Fuel Leakage
1.
Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there
are no fuel leakage at connection points.
NOTE:
Use mirrors for checking at points out of clear sight.
2.
Start the engine. With engine speed increased, check again that there are no fuel leakage at connection
points.
CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.
EM-170
< REMOVAL AND INSTALLATION >
[MR20DD]
IGNITION COIL, SPARK PLUG AND ROCKER COVER
IGNITION COIL, SPARK PLUG AND ROCKER COVER
Exploded View
INFOID:0000000010715487
Removal and Installation
INFOID:0000000010715488
REMOVAL
1.
Remove intake manifold. Refer to
2.
Remove PCV valve and PCV hose, if necessary.
Ignition coil
Spark plug
Rocker cover
Rocker cover gasket
Oil filler cap
PCV valve
O-ring
Comply with the installation proce-
dure when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA6815GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст