Nissan Qashqai J11. Manual — part 58
IGNITION COIL, SPARK PLUG AND ROCKER COVER
EM-171
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3.
Remove ignition coil.
CAUTION:
• Never drop or shock ignition coil.
• Never disassemble ignition coil.
4.
Remove rocker cover.
• Loosen bolts in the order from 7 to 1 shown in the figure.
5.
Remove rocker cover gasket from rocker cover.
6.
Use scraper to remove all traces of liquid gasket from camshaft bracket.
CAUTION:
Never scratch or damage the mating surface when cleaning off old liquid gasket.
INSTALLATION
CAUTION:
Do not reuse O-ring.
1.
Install the rocker cover gasket to rocker cover.
CAUTION:
Check the gasket is not dropped.
2.
Install rocker cover.
• Tighten bolts in two steps separately in the order from 1 to 7 as
shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
JPBIA6816ZZ
1st step
: 1.96 N·m (0.20 kg-m, 17 in-lb)
2nd step
: 8.33 N·m (0.85 kg-m, 74 in-lb)
JPBIA6816ZZ
EM-172
< UNIT REMOVAL AND INSTALLATION >
[MR20DD]
ENGINE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000010715489
MT Model
CVT Model
Engine mounting insulator (RH)
Rubber
Engine mounting insulator (LH)
Engine mounting frame support (LH)
Engine mounting bracket support
(LH)
Rear torque rod
Rear torque rod bracket
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
E1BIA1177GB
ENGINE ASSEMBLY
EM-173
< UNIT REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000010715490
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.
CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations.
• Never start working until exhaust system and coolant are cool enough.
• If items or work required are not covered by the engine section, refer to the applicable sections.
• Always use the support point specified for lifting.
• Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoid-
able reasons, support at the rear axle jacking point with a transmission jack or similar tool before
starting work, in preparation for the backward shift of center of gravity.
Engine mounting insulator (RH)
Rear torque rod bracket
Rear torque rod
Engine mounting bracket (LH)
Stud bolt
Engine mounting bracket support
(LH)
Engine mounting insulator (LH)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
E1BIA1178GB
EM-174
< UNIT REMOVAL AND INSTALLATION >
[MR20DD]
ENGINE ASSEMBLY
• For supporting points for lifting and jacking point at rear axle, refer to
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
Outline
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the tran-
saxle.
Preparation
1.
Release the fuel pressure. Refer to
.
2.
Drain engine coolant from radiator. Refer to
.
CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belts.
3.
Remove the following parts.
• Engine under cover.
• Front road wheels and tires: Refer to
(without TPMS).
• Front fender protector (RH and LH): Refer to
• Drive belts: Refer to
.
• Engine cover.
• Battery: Refer to
PG-155, "Removal and Installation"
.
• Battery tray: Refer to
• TCM: Refer to
. (CVT models)
• Air duct, air duct assembly, and air cleaner assembly: Refer to
.
• Radiator hose (upper and lower): Refer to
• Exhaust front tube: Refer to
.
Engine Room LH
1.
Disconnect all connections of engine harness around the battery, and then temporarily secure the engine
harness into the engine side.
CAUTION:
Protect connectors using a resin bag against foreign materials during the operation.
2.
Disconnect fuel feed tube at engine side.
3.
Disconnect heater hoses
4.
Disconnect control cable from transaxle. Refer to
(CVT models) or
(MT models).
5.
Remove EVAP hoses. Refer to
.
Engine Room RH
1.
Disconnect vacuum hose from intake manifold. Refer to
.
2.
Disconnect A/C piping from A/C compressor. Refer to
(Type 3) or
(Type 4).
3.
Disconnect ground cable above the alternator.
Vehicle Underbody
1.
Disconnect steering lower joint at steering gear assembly side, and release steering shaft. Refer to
2.
Remove ground cable at transaxle side.
3.
Remove rear propeller shaft. Refer to
. (4WD models)
4.
Remove front wheel sensor (RH and LH) for ABS from steering knuckle. Refer to
5.
Remove lock plate of brake hose from strut. Refer to
BR-19, "FRONT : Exploded View"
(LHD models) or
BR-63, "FRONT : Exploded View"
(RHD models).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст