Nissan Qashqai J11. Manual — part 1221
HOOD
DLK-153
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Hood assembly
2.
Front combination lamp
3.
Front fender assembly
4.
Hood bumper rubber
5.
Hood hinge
6.
Hood lock assembly
: Vehicle front
:N·m (kg-m, ft-lb)
:Body grease
JMKIB4355GB
DLK-154
< REMOVAL AND INSTALLATION >
[TYPE 1]
HOOD
HOOD HINGE : Inspection
INFOID:0000000010434680
Check hood hinge rotating part for poor lubrication. Apply body
grease if necessary.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010434681
REMOVAL
CAUTION:
Two workers are required to support the hood.
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported with appropriate material when removing
hood assembly.
2.
Remove hood support rod from hood rod grommet.
3.
Remove hood rod grommet from hood assembly.
INSTALLATION
Install in the reverse order of removal.
HOOD INSULATOR
HOOD INSULATOR : Removal and Installation
INFOID:0000000010434682
REMOVAL
1.
Fully open hood assembly.
2.
Remove hood rod clamp from hood assembly.
3.
Remove hood insulator clips, and then remove hood insulator.
INSTALLATION
Install in the reverse order of removal.
: Body grease
JMKIB2933ZZ
HOOD
DLK-155
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD HINGE : Inspection
INFOID:0000000010434680
Check hood hinge rotating part for poor lubrication. Apply body
grease if necessary.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010434681
REMOVAL
CAUTION:
Two workers are required to support the hood.
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported with appropriate material when removing
hood assembly.
2.
Remove hood support rod from hood rod grommet.
3.
Remove hood rod grommet from hood assembly.
INSTALLATION
Install in the reverse order of removal.
HOOD INSULATOR
HOOD INSULATOR : Removal and Installation
INFOID:0000000010434682
REMOVAL
1.
Fully open hood assembly.
2.
Remove hood rod clamp from hood assembly.
3.
Remove hood insulator clips, and then remove hood insulator.
INSTALLATION
Install in the reverse order of removal.
: Body grease
JMKIB2933ZZ
DLK-156
< REMOVAL AND INSTALLATION >
[TYPE 1]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
HRA2DDT
HRA2DDT : Exploded View
INFOID:0000000010434683
HRA2DDT : Removal and Installation
INFOID:0000000010434684
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-179, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
10. Remove A/C pipe bracket mounting bolt. Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3298GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст