Nissan Qashqai J11. Manual — part 93
TIMING BELT
EM-311
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
18. Remove TDC set pin [SST: KV113B0130 (Mot. 1489)] and TDC set pin [SST: KV113B0110 (Mot. 1430)].
19. Apply liquid gasket to the thread of TDC pin plug.
20. Install TDC pin plug.
21. Install the cylinder head suspended bracket.
22. Install the lower timing cover by positioning the tab (M) into the
hole (N) on the inner timing cover.
: 20 N·m (2.0 kg-m, 15 ft-lb)
: 21 N·m (2.1 kg-m, 15 ft-lb)
MBIB0512E
MBIB0513E
EM-312
< REMOVAL AND INSTALLATION >
[K9K]
TIMING BELT
23. Install the upper timing cover.
24. Install the water pipe.
25. Install the two water hoses.
26. Install the drive belt.
CAUTION:
• Make sure belt is correctly engaged with the pulley groove.
• Check for oil and coolant on belt and each pulley groove.
27. Make sure that tension of each belt is within the standard.
MBIB0514E
MBIB0515E
: 22 N·m (2.2 kg-m, 16 ft-lb)
MBIB0356E
CAMSHAFT
EM-313
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAMSHAFT
Exploded View
INFOID:0000000010282092
Removal and Installation
INFOID:0000000010282093
CAUTION:
Apply new engine oil to parts marked in illustration before installation.
REMOVAL
1.
Remove the following parts.
• Battery ground cable
• Undercover
• RH front wheel
• RH head light assembly
2.
Remove right side splash cover.
3.
Remove engine cover.
4.
Remove air inlet tube and electric throttle control actuator. Refer to
5.
Remove vacuum pump. Refer to
6.
Remove drive belt. Refer to
7.
Remove rocker cover. Refer to
EM-303, "Removal and Installation"
8.
Support underneath of engine by setting a manual lift table caddy (commercial service tool) or equivalent
tool.
CAUTION:
1.
Camshaft sprocket stud bolt
2.
Camshaft sprocket
3.
Oil seal
4.
Camshaft bracket
5.
Camshaft
6.
Cylinder head suspended bracket
7.
Valve lifter
8.
Cap
9.
Cylinder head
A.
30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
Refer to
E1BIA0023GB
EM-314
< REMOVAL AND INSTALLATION >
[K9K]
CAMSHAFT
Put a piece of wood or something similar as supporting surface, secure a completely stable condi-
tion.
9.
Remove timing belt. Refer to
EM-305, "Removal and Installation"
10. Remove camshaft brackets.
11. Remove camshaft.
12. Remove valve lifter.
INSTALLATION
1.
Install valve lifter.
2.
Install camshaft.
3.
Install camshaft bracket and tighten bolts in numerical order as
shown in the figure.
4.
Screw the shouldered rod of camshaft seal insert [SST:
KV113B0230 (Mot. 1632)] onto the stud of the camshaft.
5.
Install the old seal on the camshaft.
6.
For the new seal, put the protector with the seal on the cam-
shaft, taking care not to touch the seal.
7.
Install the cover (E) and the collar nut (F) of camshaft seal insert
[SST: KV113B0230 (Mot. 1632)].
: 11 N·m (1.1 kg-m, 8 ft-lb)
E1BIA0050ZZ
MBIB0430E
MBIB0431E
MBIB0432E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст