Nissan Qashqai J11. Manual — part 110
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
EM-379
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Loosen mounting bolts in reverse order as shown in the figure.
INSTALLATION
Note the following, and install in the reverse order of removal.
Multifunction support bracket
• Tighten mounting bolts in numerical order as shown in the figure.
Idler roller bracket (without A/C Models)
• Tighten mounting bolts in numerical order as shown in the figure.
Idler pulley bolt
• Tighten drive belt idler pulley bolt.
Auto-tensionner bolts
• Tighten drive belt auto-tensionner bolts.
Idler roller bolt (without A/C Models)
• Tighten drive belt idler roller bolt (without A/C Models).
: Engine front
E1BIA0611ZZ
: Engine front
E1BIA0611ZZ
: Engine front
E1BIA1155ZZ
Drive belt idler pulley bolt
44 Nm (4.5kg-m, 32ft-lb)
Drive belt auto-tensionner
bolts
25 Nm (2.6kg-m, 18ft-lb)
Drive belt idler roller bolt
45 Nm (4.7kg-m, 34ft-lb)
EM-380
< REMOVAL AND INSTALLATION >
[R9M]
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000010281971
for symbols in the figure.
Removal and Installation
INFOID:0000000010499449
REMOVAL
1.
Remove air duct (air cleaner side).
2.
Remove air duct (inlet side).
3.
Disconnect mass air flow sensor.
4.
Disconnect air hose from air cleaner filter unit.
5.
Remove air cleaner filter unit.
6.
Remove air hose.
7.
Remove air filter element if necessary.
INSTALLATION
• Install in the reverse order of removal.
Inspection
INFOID:0000000010281973
INSPECTION AFTER REMOVAL
1.
Clip
2.
Air duct (inlet side)
3.
Air duct (air cleaner side)
4.
Holder
5.
Air filter element
6.
Air cleaner filter unit
7.
Mass air flow sensor
8.
Resonator
9.
Clamp
10. Air hose
11.
Mounting rubber
12. Air cleaner filter unit bracket
E1BIA1200GB
AIR CLEANER AND AIR DUCT
EM-381
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Inspect air ducts, air cleaner and hose for crack or tear.
• If anything found, replace air duct assembly.
EM-382
< REMOVAL AND INSTALLATION >
[R9M]
CHARGE AIR COOLER
CHARGE AIR COOLER
Exploded View
INFOID:0000000010281974
Removal and Installation
INFOID:0000000010499450
REMOVAL
Air inlet hose and tube.
1.
Remove engine cover.
2.
Remove air inlet hose and tube. Refer to
Charge air cooler.
1.
Remove front bumper. Refer to
1.
Silencer
2.
Air inlet hose 1
3.
Clamp Air inlet hose 2
4.
Air inlet tube 1
5.
Air inlet hose 2
6.
Air inlet tube 2
7.
Charge air cooler
8.
Metal clip
9.
Air inlet tube 2 bracket
10. Cylinder head air inlet pipe
11.
Air inlet tube 1 bracket
A.
To turbocharger
B.
To throttle chamber
E1BIA1201GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст