Nissan Qashqai J11. Manual — part 109
AIR CLEANER FILTER
EM-375
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER FILTER
Removal and Installation
INFOID:0000000010281967
REMOVAL
1.
Press the points (A) to separate air resonator from air duct and
air cleaner filter unit.
2.
Remove air resonator following the arrow.
3.
Unhook clips (1) on the air cleaner filter holder.
E1BIA1002ZZ
E1BIA1003ZZ
E1BIA1004ZZ
EM-376
< PERIODIC MAINTENANCE >
[R9M]
AIR CLEANER FILTER
4.
Separate air cleaner filter holder (1) from air cleaner filter unit
and remove air cleaner filter (2).
INSTALLATION
Install in the reverse order of removal.
E1BIA1005ZZ
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
EM-377
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
Exploded View
INFOID:0000000010281969
With A/C
Without A/C
1.
Crankshaft pulley bolt
2.
Crankshaft spacer
3.
Crankshaft pulley
4.
Water pump
5.
Drive belt auto-tensionner bolt
6.
Drive belt auto-tensionner
7.
Multifunction support bracket
8.
Multifunction support bracket bolt
9.
Multifunction support bracket bolt
10. Alternator
11.
Alternator bolt
12. A/C compressor bolt
13. Compressor
14. Idler pulley
15. Idler pulley bolt
16. Idler pulley cap
17. Drive belt
A.
B.
Refer to
C.
E1BIA1198GB
EM-378
< REMOVAL AND INSTALLATION >
[R9M]
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
for symbols in the figure.
Removal and Installation
INFOID:0000000010281970
CAUTION:
• Replace the drive belt that has been removed with a new one.
• Drive belt auto-tensioner and idler pulley must be replaced with new ones when the drive belt is
replaced.
• Never run the engine without the drive belt to avoid damaging the crankshaft pulley.
REMOVAL
1.
Remove drive belt. Refer to
EM-373, "Removal and Installation"
• Keep drive belt auto-tensioner pulley arm locked after drive belt is removed.
2.
Remove drive belt auto-tensioner.
3.
Remove cover and idler pulley.
4.
Remove cover and idler roller (without A/C Models)
5.
Remove multifunction support bracket with the following procedure:
a.
Disconnect the battery cable from the negative terminal.
b.
Remove alternator. Refer to
CHG-31, "R9M : Removal and Installation"
c.
Remove A/C compressor (if equipped). Refer to
HA-121, "Removal and Installation"
d.
Remove multifunction support bracket.
1.
Crankshaft pulley bolt
2.
Crankshaft spacer
3.
Crankshaft pulley
4.
Water pump
5.
Drive belt auto-tensionner bolt
6.
Drive belt auto-tensionner
7.
Multifunction support bracket
8.
Multifunction support bracket bolt
9.
Multifunction support bracket bolt
10. Alternator
11.
Alternator bolt
12. Idler roller bracket
13. Idler roller
14. Idler roller bolt cap
15. Idler pulley
16. Idler pulley bolt
17. Idler pulley bolt cap
18. Drive belt
A.
B.
Refer to
C.
E1BIA1199GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст