Nissan Qashqai J11. Manual — part 2220
DAS-294
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
U1A39-00 COMBINATION METER COMMUNICATION
1.
Turn the ignition switch OFF.
2.
Disconnect combination meter harness connector.
3.
Check combination meter harness connector terminals (CAN communication line) or damage or loose
connection.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Recheck terminals for damage or loose connection. Refer to
DAS-210, "Precautions for Harness
, and GO TO 4.
4.
PFEFORM SELF-DIAGNOSIS (COMBINATION METER)
With CONSULT
1.
Connect combination meter harness connector.
2.
Erase self-diagnosis result for “MATER/M&A”.
3.
Turn the ignition switch OFF and wait for 10 seconds or more.
4.
Turn the ignition switch ON.
5.
Perform self-diagnosis for “METER/M&A”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 5.
5.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Connect chassis control module harness connector.
2.
Erase self-diagnosis result for “CHASSIS CONTROL”.
3.
Turn the ignition switch OFF and wait for 10 seconds or more.
4.
Turn the ignition switch ON.
5.
Perform “All DTC Reading”.
Is DTC “U1000-00”, “U1A39-00” or other DTC detected?
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (“U1A39-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
U1A3B-00 TCM COMMUNICATION
DAS-295
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U1A3B-00 TCM COMMUNICATION
DTC Description
INFOID:0000000010417051
DTC DETECTION LOGIC
POSSIBLE CAUSE
• TCM
• Chassis control module
• CAN communication line
FAIL-SAFE
The following functions are suspended.
• Active Trace Control function
• Active Ride Control (engine) function
• Active Engine Brake
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “U1A3B-00” detected?
YES
>> Proceed to
DAS-295, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417052
1.
CHECK CAN DIAGNOSIS SUPPORT MONITOR
With CONSULT
1.
Select “CAN Diagnosis Support Monitor” of “CHASSIS CONTROL”.
2.
Check malfunction between each control unit connected to chassis control module.
Check the result of “PRESENT”?
>> Refer to
LAN-39, "CAN COMMUNICATION SYSTEM : CAN Communication Control Circuit"
.
“TRANSMIT DIAG” is other than “OK”>>GO TO 2.
“TRANSMISSION” other than “OK”>>GO TO 3.
2.
CHECK TRANSMITTING SIDE UNIT
1.
Turn the ignition switch OFF.
2.
Disconnect chassis control module harness connector.
3.
Check the chassis control module harness connector terminals No. 3 and 4 for damage or loose connec-
tion.
Is the inspection result normal?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
U1A3B-00
TCM COMM
(TCM communication)
When chassis control module is not receiving CAN communication signal (be-
tween chassis control module and TCM) for 2 seconds or more.
DAS-296
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
U1A3B-00 TCM COMMUNICATION
YES
>> GO TO 5.
NO
>> Recheck terminals for damage or loose connection. Refer to
DAS-210, "Precautions for Harness
, and GO TO 5.
3.
CHECK TCM
1.
Turn the ignition switch OFF.
2.
Disconnect TCM harness connector.
3.
Check TCM harness connector terminals (CAN communication line) or damage or loose connection.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Recheck terminals for damage or loose connection. Refer to
DAS-210, "Precautions for Harness
, and GO TO 4.
4.
PFEFORM SELF-DIAGNOSIS (TCM)
With CONSULT
1.
Connect TCM harness connector.
2.
Erase self-diagnosis result for “TRANSMISSION”.
3.
Turn the ignition switch OFF and wait for 10 seconds or more.
4.
Turn the ignition switch ON.
5.
Perform self-diagnosis for “TRANSMISSION”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(RE0F10D) or
(RE0F10G).
NO
>> GO TO 5.
5.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Connect chassis control module harness connector.
2.
Erase self-diagnosis result for “CHASSIS CONTROL”.
3.
Turn the ignition switch OFF and wait for 10 seconds or more.
4.
Turn the ignition switch ON.
5.
Perform “All DTC Reading”.
Is DTC “U1000-00”, “U1A3B-00” or other DTC detected?
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (“U1A3B-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
U1A42-00 STEERING ANGLE SENSOR COMMUNICATION
DAS-297
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U1A42-00 STEERING ANGLE SENSOR COMMUNICATION
DTC Description
INFOID:0000000010417053
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Steering angle sensor
• Chassis control module
• CAN communication line
FAIL-SAFE
The following functions are suspended.
• Active Trace Control function
• Active Ride Control (engine) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “U1A42-00” detected?
YES
>> Proceed to
DAS-297, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417054
1.
CHECK CAN DIAGNOSIS SUPPORT MONITOR
With CONSULT
1.
Select “CAN Diagnosis Support Monitor” of “CHASSIS CONTROL”.
2.
Check malfunction between each control unit connected to chassis control module.
Check the result of “PRESENT”?
>> Refer to
LAN-39, "CAN COMMUNICATION SYSTEM : CAN Communication Control Circuit"
.
“TRANSMIT DIAG” is other than “OK”>>GO TO 2.
“STRG” other than “OK”>>GO TO 3.
2.
CHECK TRANSMITTING SIDE UNIT
1.
Turn the ignition switch OFF.
2.
Disconnect chassis control module harness connector.
3.
Check the chassis control module harness connector terminals No. 3 and 4 for damage or loose connec-
tion.
Is the inspection result normal?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
U1A42-00
STEERING ANGLE SENSOR
COMM
(Steering angle sensor communi-
cation)
When chassis control module is not receiving CAN communication signal (be-
tween chassis control module and steering angle sensor) for 2 seconds or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст