Nissan Qashqai J11. Manual — part 1431
SYSTEM
SEC-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYSTEM DESCRIPTION
• The system reduces the possibility of a theft or mischief by sounding siren and blinking hazard warning lamp
continuously. The system activates siren and hazard warning lamp when detecting that the door or hood is
opened, or there is an illegal attempt to enter into the passenger room, while the system is in the ARMED
phase.
• Security indicator lamp on combination meter always blinks when ignition switch is any position other than
ON to warn that the vehicle is equipped with a VEHICLE SECURITY SYSTEM.
• Anti-theft function is improved by the adoption of intruder sensor that detects an attempt to enter into the
passenger room.
• Activation or deactivation of intruder sensor can be selected by sensor cancel switch.
• Siren control unit equips a built-in battery. Replace siren control unit once every 10 years because the war-
ranty for built-in battery expires after 10 years.
• Each time the system switches to the ARMED phase from the PRE-ARMED phase, the self-diagnosis is per-
formed by the siren control unit and each sensor. If any malfunction is detected, the siren sounds* 5 times to
inform the driver that a malfunction is detected and the vehicle security system does not function properly.
Malfunctioning part can be checked by “SIREN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using
CONSULT. Refer to
SEC-48, "Diagnosis Description"
*: Siren sounds for 0.2 seconds and sound interval is 0.4 seconds.
Operation Flow
Reception unit
Signal name
Combination meter (security indicator lamp)
Security indicator lamp signal
Siren control unit
Alarm link signal
Hazard warning lamp
Hazard warning lamp signal
Outside key antenna
Outside key antenna signal
JMKIB1929GB
No.
System state
Switching condition
DISARMED to
FULL PRE-
ARMED
When all conditions of A and
one condition of B is satis-
fied.
A
B
• Ignition switch: OFF
• All doors: Closed
• Hood: Closed
All doors are locked by:
• LOCK button of Intelligent Key
• Door request switch
DISARMED to
PARTIAL PRE-
ARMED
When all conditions of A and
one condition of B is satis-
fied.
A
B
• Ignition switch: OFF
• Hood or any door: Open
All doors are locked by:
• LOCK button of Intelligent Key
• Door request switch
FULL PRE-
ARMED to DIS-
ARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Intelligent Key: ON
• Door request switch: ON
SEC-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
NOTE:
To lock/unlock all doors by operating remote controller button of Intelligent Key or door request switch, Intelligent Key must be within the
detection area of outside key antenna. For details, refer to
.
Disarmed Phase
VEHICLE SECURITY SYSTEM switches to the DISARMED phase while any doors or hood is open because it
is assumed that the owner is in or nearby the vehicle.
Pre-armed Phase
• VEHICLE SECURITY SYSTEM switches to the PRE-ARMED phase and blinks security indicator lamp
quickly for approximately 20 seconds when all doors are locked by Intelligent Key or door request switch,
while all doors and hood are closed.
PARTIAL PRE-
ARMED to DIS-
ARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Intelligent Key: ON
• Door request switch: ON
PARTIAL PRE-
ARMED to FULL
PRE-ARMED
When all of the following
conditions are satisfied.
• All doors: Closed
• Hood: Closed
FULL PRE-
ARMED to PAR-
TIAL PRE-ARMED
When one of the following
condition is satisfied.
• Any door: Opened
• Hood: Opened
FULL PRE-
ARMED to FULL
ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
• All doors: Locked
• Hood: Closed
PARTIAL PRE-
ARMED to PAR-
TIAL ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
• Hood or any door: Open
PARTIAL to FULL
ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
• All doors: Closed
• Hood: Closed
FULL ARMED to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Intelligent Key: ON
• Door request switch: ON
PARTIAL ARMED
to DISARM
FULL ARMED to
ALARM
When one of the following
condition is detected.
• Any door or hood is opened
• Battery is connect and disconnect
• Movement to enter into passenger room
• Communication between BCM and siren control unit is interrupted
• Communication between siren control unit and intruder sensor is in-
terrupted
PARTIAL ARMED
to ALARM
When one of the following
condition is detected.
• Any door or hood is opened
• Battery is connect and disconnect
• Communication between BCM and siren control unit is interrupted
• Communication between siren control unit and intruder sensor is in-
terrupted
ALARM to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Intelligent Key: ON
• Door request switch: ON
ALARM to ALARM
PAUSE
27.5 seconds are passed.
ARM PAUSE to
FULL ARMED
5 seconds are passed after deactivating ALARM.
ARM PAUSE to
PARTIAL ARMED
ALARM PAUSE to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Intelligent Key: ON
• Door request switch: ON
No.
System state
Switching condition
SYSTEM
SEC-25
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
• VEHICLE SECURITY SYSTEM that is in the PRE-ARMED phase switches to the DISARMED phase when
all doors are unlocked by Intelligent Key or door request switch.
• VEHICLE SECURITY SYSTEM does not activate siren when door or hood is open while VEHICLE SECU-
RITY SYSTEM is in the PRE-ARMED phase. When the door or hood is closed again, VEHICLE SECURITY
SYSTEM stays in the PRE-ARMED phase.
Armed Phase
VEHICLE SECURITY SYSTEM switches to the ARMED phase from the PRE-ARMED phase after approxi-
mately 20 seconds, and blinks security indicator lamp slowly.
Alarm Phase
• VEHICLE SECURITY SYSTEM activates siren for approximately 27.5 seconds when any of the following
conditions is fulfilled while VEHICLE SECURITY SYSTEM is in the ARMED phase.
- When any door or hood is open
- When power supply to siren control unit is blocked
- When intruder sensor detects an attempt to enter into passenger compartment
- When battery connection is disconnected
• VEHICLE SECURITY SYSTEM deactivates siren when door is unlocked by Intelligent Key or door request
switch, or the ignition switch is switched to the ON position while siren is activated.
• VEHICLE SECURITY SYSTEM switches to the ARMED phase automatically when approximately 5 sec-
onds pass after deactivating siren.
SENSOR CANCEL FUNCTION
Perform the following procedure to deactivate intruder sensor.
1.
CHECK SENSOR CANCEL FUNCTION
1.
Turn ignition switch OFF.
2.
Press sensor cancel switch, and before 5 minutes pass, close all doors and hood, and lock all doors using
the Intelligent Key or door request switch.
3.
Check that VEHICLE SECURY SYSTEM is switched to the PRE-ARMED phase and that the siren sounds
one beep.
NOTE:
Intruder sensor is not cancelled and return to normal operation when any of the following conditions is fulfilled
while the cancellation procedure is being performed.
• When ignition switch turns ON.
• When 5 minutes or more pass after pressing sensor cancel switch.
• When VEHICLE SECURITY SYSTEM switches to the DISARMED phase.
Does security indicator lamp blink quickly?
YES
>> INSPECTION END
NO
>> Check again.
SEC-26
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010479100
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
—
AIR CONDITONER*
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст