Nissan Qashqai J11. Manual — part 1774
LUGGAGE ROOM LAMP CIRCUIT
INL-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Is the inspection result normal?
YES
>> Replace luggage room lamp.
NO
>> Repair or replace harnesses.
4.
CHECK LUGGAGE ROOM LAMP SHORT CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
BCM
Luggage room lamp
Continuity
Connector
Terminal
Connector
Terminal
B3
127
B49
4
Existed
BCM
Ground
Continuity
Connector
Terminal
B3
127
Not existed
INL-62
< DTC/CIRCUIT DIAGNOSIS >
SPICY ILLUMINATION CIRCUIT
SPICY ILLUMINATION CIRCUIT
Component Function Check
INFOID:0000000010503098
NOTE:
Before performing the diagnosis, check that Interior room lamp power supply is normal.
1.
CHECK SPICY ILLUMINATION CONTROL FUNCTION
CONSULT ACTIVE TEST
1.
Turn ignition switch ON.
2.
Select “INT LAMP” of BCM (INT LAMP) active test item.
3.
With operating the test items, check that spicy illumination turns ON/OFF.
Does spicy illumination turns ON/OFF?
YES
>> Spicy illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010503099
1.
CHECK SPICY ILLUMINATION POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove interior room lamp relay.
3.
Disconnect spicy illumination connector.
4.
Check continuity between interior room lamp relay harness connector and spicy illumination harness con-
nector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harnesses.
2.
CHECK SPICY ILLUMINATION CONTROL OUTPUT
CONSULT ACTIVE TEST
1.
Turn ignition switch ON.
2.
Select “INT LAMP” of BCM (INT LAMP) active test item.
3.
With operating the test item, check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO-1
>> Continuity exists and remains unchanged: GO TO 4.
NO-2
>> Continuity does not exist and remains unchanged: Replace BCM. Refer to
.
3.
CHECK SPICY ILLUMINATION OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and spicy illumination harness connector.
On
: Spicy illumination gradual brightening
Off
: Spicy illumination gradual dimming
Interior room lamp relay
Spicy illumination
Continuity
Connector
Terminal
Connector
Terminal
M80
7
Spicy illumination LH
M87
4
Existed
Spicy illumination LH
M88
4
BCM
Ground
Test item
Continuity
Connector
Terminal
M70
72
INT LAMP
On
Existed
Off
Not existed
SPICY ILLUMINATION CIRCUIT
INL-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Is the inspection result normal?
YES
>> Replace spicy illumination.
NO
>> Repair or replace harnesses.
4.
CHECK SPICY ILLUMINATION SHORT CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
BCM
Spicy illumination
Continuity
Connector
Terminal
Connector
Terminal
M70
72
Spicy illumination LH
M87
3
Existed
Spicy illumination LH
M88
3
BCM
Ground
Continuity
Connector
Terminal
M70
72
Not existed
INL-64
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Component Function Check
INFOID:0000000010430919
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT ACTIVE TEST
1.
Turn ignition switch ON.
2.
Select “ENGINE SW ILLUMI” of BCM (INTELLIGENT KEY) active test item.
3.
With operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
Does the push-button ignition switch illumination turns ON/OFF?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010430920
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OUTPUT
CONSULT ACTIVE TEST
1.
Turn ignition switch ON.
2.
Select ENGINE SW ILLUMI of BCM (INTELLIGENT KEY) active test item.
3.
With operating the test item, check the voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and push-button ignition switch connector.
3.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harnesses.
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace push-button ignition switch.
On
: Push-button ignition switch illumination ON
Off
: Push-button ignition switch illumination OFF
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M69
88
Ground
ENGINE SW ILLUMI
On
12 V
Off
0 V
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M69
88
M31
5
Existed
Push-button ignition switch
—
Continuity
Connector
Terminal
M31
6
Ground
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст