Nissan Qashqai J11. Manual — part 807
DLN-144
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY30A]
AWD WARNING LAMP DOES NOT TURN ON
AWD WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000010288312
AWD warning lamp does not turn ON when the ignition switch is turned to ON.
Diagnosis Procedure
INFOID:0000000010288313
1.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis for AWD warning lamp. Refer to
DLN-126, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the malfunctioning part.
AWD WARNING LAMP DOES NOT TURN OFF
DLN-145
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000010288314
AWD warning lamp does not turn OFF several seconds after engine started.
Diagnosis Procedure
INFOID:0000000010288315
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform AWD control unit self-diagnosis.
Is any error system detected?
YES
>> Check the error system.
NO
>> GO TO 2.
2.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis of the AWD warning lamp. Refer to
DLN-126, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK AWD CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis of the power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the malfunctioning part.
DLN-146
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY30A]
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
Description
INFOID:0000000010288316
Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.
Diagnosis Procedure
INFOID:0000000010288317
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform ECM self-diagnosis.
Is any error system detected?
YES
>> Check the error system.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform AWD control unit self-diagnosis.
Is DTC “U1000” detected?
YES
>> CAN specification chart. Refer to
LAN-24, "Trouble Diagnosis Flow Chart"
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
DLN-113, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CHECK ELECTRIC CONTROLLED COUPLING
1.
Turn the ignition switch OFF.
2.
Set the transaxle to neutral. Release the parking brake.
3.
Lift up the vehicle.
4.
Rotate the propeller shaft by hand.
5.
Hold rear wheel of right and left lightly.
Does rear wheel rotate?
YES
>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to
NO
>> Check each harness connector pin terminal for disconnection.
VEHICLE DOES NOT ENTER AWD MODE
DLN-147
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
VEHICLE DOES NOT ENTER AWD MODE
Description
INFOID:0000000010288318
Vehicle does not enter AWD mode even though AWD warning lamp turned to OFF.
Diagnosis Procedure
INFOID:0000000010288319
1.
CHECK AWD WARNING LAMP
Turn the ignition switch ON.
Does AWD warning lamp turn ON?
YES
>> GO TO 2.
NO
>> Go to
DLN-144, "Diagnosis Procedure"
.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform AWD control unit self-diagnosis.
Is DTC “U1000” detected?
YES
>> CAN specification chart. Refer to
LAN-24, "Trouble Diagnosis Flow Chart"
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
DLN-113, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CRUISE TEST
Drive the vehicle for a period of time.
Does any symptom occur?
YES
>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of
clutch is not possible). Refer to
NO
>> Check each harness connector pin terminal for disconnection.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст