Nissan Qashqai J11. Manual — part 1210
OUTSIDE KEY ANTENNA
DLK-109
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> Replace outside key antenna (rear bumper).
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
DLK-110
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
FRONT DOOR
FRONT DOOR : Diagnosis Procedure
INFOID:0000000010479727
1.
CHECK FUSE
Check that the following fuse is not fusing.
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connectors.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
REAR DOOR
REAR DOOR : Diagnosis Procedure
INFOID:0000000010479728
1.
CHECK FUSE
Check that the following fuse is not fusing.
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connectors.
Signal name
Fuse No.
Front door lock actuator power supply
29 (15 A)
(+)
(
−
)
Voltage
BCM
Connector
Terminal
M68
143
Ground
9 – 16 V
BCM
Ground
Continuity
Connector
Terminal
M68
146
Existed
147
Signal name
Fuse No.
Passenger door and rear door lock actuator power supply
31 (15 A)
POWER SUPPLY AND GROUND CIRCUIT
DLK-111
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
(+)
(
−
)
Voltage
BCM
Connector
Terminal
M68
151
Ground
9 – 16 V
BCM
Ground
Continuity
Connector
Terminal
M68
146
Existed
147
DLK-112
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
SUPER LOCK ACTUATOR
SUPER LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010479719
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-112, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010479720
1.
CHECK SUPER LOCK ACTUATOR SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM and each door lock assembly.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
Front door lock assembly (driver side)
Connector
Terminal
D26
1
Ground
Super lock
Set
9 – 16 V
2
Release
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
148
D26
2
Existed
149
1
BCM
Ground
Continuity
Connector
Terminal
M68
148
Not existed
149
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст