Nissan Qashqai J11. Manual — part 1340
BACK DOOR
DLK-629
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Fix back door stay (1) using a vise (C)
CAUTION:
When cutting a hole on back door stay, always cover a
hacksaw (A) using a shop cloth (B) to avoid scattering
metal fragments or oil.
2.
Slowly cut a hole and drain the gas in the order of 1
→
2 as
shown in the figure using a hacksaw at 2 positions of (1) and (2).
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000010479441
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark with vehicle center position mark and
install weather-strip onto the vehicle.
2.
For the lower section, align the weather-strip seam with center of back door striker.
3.
Pull weather-strip gently to ensure that there is no loose section.
CAUTION:
Securely fit each corner.
JMKIA3336ZZ
A
: 20 mm (0.787 in)
B
: Cat at the groove
JMKIA3609ZZ
DLK-630
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000010479496
LHD models
JMKIB3309GB
1.
Hood lock control handle
2.
Hood lock assembly
3.
Hood safety hook
4.
Hood lock control cable
: Clip
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
HOOD LOCK
DLK-631
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RHD models
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000010479443
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove hood lock assembly mounting bolt and nuts, and then remove hood lock assembly from radiator
core support upper.
3.
Disconnect hood lock control cable assembly from hood lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• After installation, perform hood lock control inspection. Refer to
.
• Check hood lock assembly for poor lubrication. Refer to
• After installation, perform hood fitting adjustment. Refer to
DLK-601, "HOOD ASSEMBLY : Adjust-
HOOD LOCK CONTROL HANDLE
JMKIB3308GB
1.
Hood lock control handle
2.
Hood lock control cable
3.
Hood safety hook
4.
Hood lock assembly
: Clip
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
DLK-632
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD LOCK
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010479502
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect hood lock control cable (2) from hood opener lever (1) according to the numerical order 1
→
2
indicated by arrows as shown in the figure.
• LHD models
• RHD models
3.
Disconnect fuel opener cable from fuel filler lid opener lever of hood lock control handle. Refer to
647, "FUEL FILLER OPENER CABLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010479445
REMOVAL
1.
Disconnect hood lock control cable from hood lock assembly. Refer to
2.
Remove fender protector (driver side). Refer to
EXT-33, "Removal and Installation"
3.
Remove hood lock control cable fixing clips.
4.
Disconnect hood lock control cable from hood lock control handle. Refer to
CONTROL HANDLE : Removal and Installation"
.
5.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
JMKIB0324ZZ
JMKIB0327ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст