Nissan Qashqai J11. Manual — part 1307
FRONT DOOR LOCK
DLK-497
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove front rear glass run. Refer to
GW-23, "Removal and Installation"
5.
Remove key rod protector mounting bolts, and then remove key rod protector.
6.
Disengage outside handle cable from cable clip.
7.
Disengage rod holder, and then disconnect key rod from door lock assembly. (Driver side only)
8.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
9.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
10. While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
11. Remove front gasket (1) and rear gasket (2).
JMKIB0585ZZ
JMKIA0441ZZ
JMKIA2948ZZ
: Pawl
: Vehicle front
JMKIB2240ZZ
DLK-498
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR LOCK
12. Slide outside handle bracket toward rear of vehicle to remove.
13. Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5935ZZ
JMKIA5936ZZ
REAR DOOR LOCK
DLK-499
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000010479390
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010479391
REMOVAL
1.
Remove inside handle. Refer to
DLK-500, "INSIDE HANDLE : Removal and Installation"
.
2.
Remove outside handle bracket. Refer to
DLK-500, "OUTSIDE HANDLE : Removal and Installation"
1.
Outside handle escutcheon
2.
Outside handle grip
3.
Front gasket
4.
Cable clip
5.
Inside handle
6.
Door lock assembly
7.
TORX bolt
8.
Outside handle bracket
9.
Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3254GB
DLK-500
< REMOVAL AND INSTALLATION >
[TYPE 3]
REAR DOOR LOCK
3.
Remove rear door lower sash mounting bolt, and then remove rear door lower sash.
4.
Disconnect door lock assembly harness connector.
5.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Refer to
DLK-500, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010479392
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010479393
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010479394
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
: Body grease
JMKIA8534ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст