Nissan Qashqai J11. Manual — part 1306
HOOD LOCK
DLK-493
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check hood lock assembly for poor lubrication. Refer to
• After installation, perform hood fitting adjustment. Refer to
DLK-465, "HOOD ASSEMBLY : Adjust-
HOOD LOCK CONTROL HANDLE
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010479381
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect hood lock control cable (2) from hood opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Disconnect fuel opener cable from fuel filler lid opener lever of hood lock control handle. Refer to
507, "FUEL FILLER OPENER CABLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010479382
REMOVAL
1.
Disconnect hood lock control cable from hood lock assembly. Refer to
2.
Remove fender protector (driver side). Refer to
EXT-33, "Removal and Installation"
3.
Remove hood lock control cable fixing clips.
4.
Disconnect hood lock control cable from hood lock control handle. Refer to
CONTROL HANDLE : Removal and Installation"
.
5.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
JMKIB0327ZZ
PIIB5801E
DLK-494
< REMOVAL AND INSTALLATION >
[TYPE 3]
HOOD LOCK
• After installation, perform hood fitting adjustment. Refer to
DLK-465, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD SAFETY HOOK
HOOD SAFETY HOOK : Removal and Installation
INFOID:0000000010497983
REMOVAL
Remove mounting nuts, and then remove hood lock secondary assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000010479384
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch is securely engaged with secondary striker from the dead load of the hood
assembly.
3.
Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall
from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
4.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
5.
Check that secondary latch is properly engaged with secondary striker [4.0 mm (0.157 in)].
6.
Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock assembly.
: Body grease
JMKIB1164ZZ
FRONT DOOR LOCK
DLK-495
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000010479385
*
1
: Driver side only
1.
Outside handle escutcheon
2.
Outside handle grip
3.
Front gasket
4.
Inside handle
5.
cable clip
6.
Door lock assembly
7.
Key rod protector*
1
8.
Key rod*
1
9.
TORX bolt
10. Outside handle bracket
11. Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3252GB
DLK-496
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010479386
REMOVAL
1.
Disconnect inside handle cable from inside handle. Refer to
DLK-496, "INSIDE HANDLE : Removal and
.
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly harness connector.
4.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock assembly for poor lubrication. Refer to
DLK-496, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010479387
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010479388
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010479389
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen.
: Body grease
JMKIA8534ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст