Nissan Qashqai J11. Manual — part 870
WT-26
< BASIC INSPECTION >
[WITH TPMS]
DIAGNOSIS AND REPAIR WORK FLOW
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “
maybe the customer mentions this symptom”.
>> GO TO 2.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP BULB
Check that low tire pressure warning lamp in combination meter turns ON when ignition switch is turned ON.
Does low tire pressure warning lamp turns ON?
YES
>> GO TO 3.
NO
>> Perform combination meter diagnosis. If combination meter is normal, perform configuration.
. And check low tire pressure warning lamp again.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP STATES (1)
Check states of low tire pressure warning lamp in combination meter when ignition switch is turned ON.
How is states of low tire pressure warning lamp?
Stays ON>>GO TO 4.
Blinks for 1 minute and then stays ON>>GO TO 5.
Turns ON for 1 second and then stays OFF>>GO TO 6.
4.
CHECK AIR LEAK
Adjust the tire pressure for all wheels specified to the value. Refer to
And then check air leak using soapsuds etc..
NOTE:
Check valve core and around valve stem too.
Is air leak detected?
YES
>> Repair or replace error-detected parts. And then GO TO 8.
NO
>> GO TO 8.
5.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors are installed correctly?
YES
>> GO TO 9.
NO
>> GO TO 7.
6.
EXPLAIN TO THE CUSTOMER
Explain the following possibilities to the customer.
• When illuminating low tire pressure warning lamp went out:
- Tire pressure was lower than the warning tire pressure value.
• When blinking low tire pressure warning lamp went out:
- Radio waves of tire pressure sensor broke off temporarily by interference of other radio waves (e.g. radio
tower, battery charger of smart phone).
- Wheel(s) to which tire pressure sensor was not installed were attached.
NOTE:
Low tire pressure warning lamp turned off since malfunction was solved in any case.
Has the customer been convinced?
YES
>> INSPECTION END
NO
>> GO TO 9.
7.
REPLACING/INSTALLING TIRE PRESSURE SENSOR
1.
Replace and/or Install tire pressure sensor(s). Refer to
WT-62, "Removal and Installation"
2.
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> GO TO 8.
DIAGNOSIS AND REPAIR WORK FLOW
WT-27
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NO
>> Perform diagnosis procedure of “TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE
. And then GO TO 8.
8.
CHECK LOW TIRE PRESSURE WARNING LAMP STATES (2)
1.
Adjust the tire pressure for all wheels specified to the value. Refer to
.
2.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
3.
Check states of low tire pressure warning lamp in combination meter when ignition switch is turned ON.
Does low tire pressure warning lamp turn ON for 1 second and then turn OFF?
YES
>> Explain to the customer that this is TPMS normal operation, and GO TO 13.
NO
>> GO TO 9.
9.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Record or print self-diagnosis results and freeze frame data (FFD). GO TO 10.
NO
>> GO TO 11.
10.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again.
Is DTC detected?
YES
>> GO TO 12.
NO
>> Check harness and connectors based on the information obtained by interview and repair or
replace error-detected parts. Refer to
GI-41, "Intermittent Incident"
. GO TO 13.
11.
CONFIRM THE SYMPTOM
Perform symptom diagnosis. refer to
>> Repair or replace error-detected parts. GO TO 13.
12.
DIAGNOSIS PROCEDURE
Perform DTC Diagnosis Procedure.
>> Repair or replace error-detected parts. GO TO 13.
13.
FINAL CHECK
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES
>> GO TO 3.
NO
>> INSTPECTION END
WT-28
< BASIC INSPECTION >
[WITH TPMS]
ADDITIONAL SERVICE WHEN REPLACING BCM
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000010339520
When replacing BCM, configuration (BCM, CAN gateway and TPMS) and then tire pressure sensor ID regis-
tration is required.
Work Procedure
INFOID:0000000010339521
1.
PERFORM CONFIGURATION (BCM)
Perform configuration BCM. Refer to
.
>> GO TO 2.
2.
PERFORM CONFIGURATION (CAN GATEWAY)
Perform configuration CAN gateway. Refer to
.
>> GO TO 3.
3.
PERFORM CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Perform configuration tire pressure monitoring system. Refer to
>> GO TO 4.
4.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
>> WORK END
TIRE PRESSURE SENSOR ID REGISTRATION
WT-29
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000010339522
This procedure must be performed:
• After replacement of a tire pressure sensor or BCM.
• After replacement of tire or road wheel.
NOTE:
ID registration is unnecessary if there are no change in the positions of each wheels (tire pressure sensors)
before wheel removal and after wheel installation.
• After performing tire rotation.
Work Procedure
INFOID:0000000010339523
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
NOTE:
Refer to the manufacture operating instructions for how to use the tire pressure sensor activation tool
[KV48105501 (NI-4032)].
With CONSULT
1.
Turn the ignition switch ON.
2.
Display the “WORK SUPPORT” screen and select “ID REGIST”.
3.
Select the start button on the “ID REGIST” screen.
4.
Contact the tire pressure sensor activation tool [KV48105501
(NI-4032)] (1) to the side of the tire at the location to the tire
pressure sensor.
5.
Press the registration button and wait until the hazard warning
lamp blinks twice.
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
6.
When ID registration is completed, check the following pattern at each wheel.
7.
After the ID registration procedure for all wheels is completed, press “End” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст