Nissan Qashqai J11. Manual — part 871
WT-30
< BASIC INSPECTION >
[WITH TPMS]
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Work Procedure
INFOID:0000000010339524
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of BCM cannot be read.
• After configuration, perform the following:
- Turn the ignition switch from OFF to ON and check that the low tire pressure warning lamp turns
OFF after staying illuminated for approximately two seconds.
- Perform tire pressure sensor ID registration. Refer to
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search BCM of the parts number and find “Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for BCM. Replace in the usual manner. Refer to
.
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “TPMS”
2.
Select “Before Replace ECU” of “Read/Write Configuration”.
3.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING BCM (1)
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
2.
Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
WT-31
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
7.
REPLACING BCM (2)
BCS-132, "Removal and Installation"
.
>> GO TO 8.
8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1.
Select “Manual Configuration”.
2.
Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
9.
VERIFYING TYPE ID (2)
Compare “Type ID” written into the BCM with the one searched by using FAST (service parts catalogue) to
check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 10.
10.
CHECKING LOW TIRE PRESSURE WARNING LAMP
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON and check that the low tire pressure warning lamp turns OFF after staying illu-
minated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Perform the self-diagnosis of “AIR PRESSURE MONITOR”. Refer to
(TIRE PRESSURE MONITORING SYSTEM)"
11.
PERFORMING SUPPLEMENTARY WORK
1.
Adjust the tire pressure to the specified value. Refer to
.
2.
Perform tire pressure sensor ID registration. Refer to
.
3.
Perform the self-diagnosis of all systems.
4.
Erase self-diagnosis results.
5.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
>> End of work.
WT-32
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Description
INFOID:0000000010339525
DTC DETECTION LOGIC
NOTE:
The actual malfunction part may differ from the malfunction part which DTC shows if ID registration is not per-
formed after performing tire rotation or tire/road wheel replacement.
POSSIBLE CAUSE
• Low tire pressure (natural air leak)
• Air leak because of wheel change
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
4.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
5.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1704”, “C1705”, “C1706”, or “C1707” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010339526
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
2.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure of all wheels. Refer to
.
CAUTION:
If the checked value is close to the standard, reduce the tire pressure, and then with the ignition
switch ON, adjust the tire pressure again so that it is within the standard.
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1704
LOW PRESSURE FL
(Low tire pressure front left)
Front left tire pressure drops.
C1705
LOW PRESSURE FR
(Low tire pressure front right)
Front right tire pressure drops.
C1706
LOW PRESSURE RR
(Low tire pressure rear right)
Rear right tire pressure drops.
C1707
LOW PRESSURE RL
(Low tire pressure rear left)
Rear left tire pressure drops.
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-33
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
4.
Drive for 2 minutes or more at a speed of between 25 km/h (16 MPH) and 100 km/h (62 MPH).
5.
Recheck the tire pressure of all wheels. Refer to
Is the inspection result normal?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
NO
>> GO TO 3
3.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Adjust tire pressure for all wheels to the specified value. Refer to
2.
Select “DATA MONITOR” in “AIR PRESSURE MONITOR”.
3.
Check that the tire pressures match the standard value.
Is the inspection result normal?
YES
>> Check air leak using soapsuds etc. and repair or replace error-detected parts. After erasing DTC
record, INSPECTION END.
NO
>> Repair or replace error-detected parts.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to the indication on tire gauge value for front left tire
AIR PRESS FR
Approximately equal to the indication on tire gauge value for front right tire
AIR PRESS RR
Approximately equal to the indication on tire gauge value for rear right tire
AIR PRESS RL
Approximately equal to the indication on tire gauge value for rear left tire
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст