Nissan Qashqai J11. Manual — part 2278
CHASSIS MAINTENANCE
MA-147
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
GEAR OIL (RS6F95R) : Refilling
INFOID:0000000011497362
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified limit at filler plug hole as shown.
2.
After refilling gear oil, check oil level. Refer to
.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
GEAR OIL (RS6F95R) : Inspection
INFOID:0000000011497363
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Never start engine while checking oil level.
2.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque.
GEAR OIL (RS6F52A)
GEAR OIL (RS6F52A) : Exploded View
INFOID:0000000011497364
GEAR OIL (RS6F52A) : Draining
INFOID:0000000011497365
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug and then drain gear oil.
3.
Set a gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SCIA7623E
SCIA7623E
JPDIC0073ZZ
MA-148
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
GEAR OIL (RS6F52A) : Refilling
INFOID:0000000011497366
1.
Remove filler plug (1). Fill with new gear oil to transaxle.
2.
After refilling gear oil, check oil level. Refer to
.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
GEAR OIL (RS6F52A) : Inspection
INFOID:0000000011497367
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1).
2.
Measure oil level using a suitable gauge (A) as shown in the fig-
ure and then check if it is within the specifications.
CAUTION:
• Never start engine while checking oil level.
• Measure suitable gauge according to the wall of the plug
mounting hole.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
CLUTCH FLUID
CLUTCH FLUID : Inspection
INFOID:0000000011497370
CLUTCH FLUID LEVEL
A
: Suitable gauge
: Vehicle front
Oil grade and viscosity
: Refer to
.
Oil capacity (reference)
: Refer to
JPDIC0139ZZ
: Vehicle front
Oil level “L”
: Refer to
JPDIC0139ZZ
CHASSIS MAINTENANCE
MA-149
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Check that the fluid level in the reservoir tank is within the specified
range (MAX – MIN lines).
• Visually check for any clutch fluid leakage around the reservoir
tank.
• Check the clutch system for any leakage if the fluid level is
extremely low (lower than MIN).
CLUTCH FLUID : Air Bleeding Procedure
INFOID:0000000011497371
NOTE:
Do not use a vacuum assist or any other type of power bleeder on this system. Use of a vacuum assist or
power bleeder will not purge all the air from the system.
CAUTION:
• Monitor clutch fluid level in reservoir tank to make sure it does not empty.
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
• Bleed the air of bleeding connector (1).
1.
Fill reservoir tank with new clutch fluid.
2.
Connect a transparent vinyl hose to air bleeder of bleeding con-
nector.
3.
“Depress” and “release” the clutch pedal slowly and fully 15
times at an interval of 2 to 3 seconds and release the clutch
pedal.
4.
Push the lock pin (1) of the bleeding connector (2), and maintain
the position.
CAUTION:
Hold it to prevent releasing clutch tube from bleeding con-
nector when fluid pressure is applied in the tube.
5.
Slide clutch tube (1) in the direction of the arrow as shown in the
figure.
•
6.
Depress the clutch pedal soon and hold it, and then bleed the air
from the piping.
CAUTION:
Hold it to prevent releasing clutch tube from bleeding con-
nector when fluid pressure is applied in the tube.
7.
Return clutch tube and lock pin to their original positions.
8.
Release clutch pedal and wait for 5 seconds.
JPFIA0007ZZ
PCIB1494E
JPDIB0041ZZ
2
: Clutch housing
Dimension “A”
: 10 mm (0.39 in)
JPDIB0042ZZ
MA-150
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
9.
Repeat steps 3 to 8 until no bubbles are observed in the clutch fluid.
TRANSFER OIL (TY21C)
TRANSFER OIL (TY21C) : Inspection
INFOID:0000000011497372
OIL LEAKS
Check that oil is not leaking from transfer assembly or around it.
OIL LEVEL
CAUTION:
Do not start engine while checking oil level.
1.
Remove filler plug (1).
2.
Oil level (A) should be level with bottom of filler plug hole. Add
oil if necessary. Refer to
MA-64, "Fluids and Lubricants"
3.
Clean threads of filler plug (1) and transfer case.
4.
Apply sealant to the threads of the filler plug (1) and install it.
Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
MA-64, "Fluids and Lubricants"
.
TRANSFER OIL (TY21C) : Draining
INFOID:0000000011497373
CAUTION:
Do not start engine while checking oil level.
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the engine and remove drain plug (1) and drain the transfer
oil.
3.
Clean threads of drain plug (1) and transfer case.
4.
Apply sealant to the threads of the drain plug (1) and install it.
Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
MA-64, "Fluids and Lubricants"
.
TRANSFER OIL (TY21C) : Refilling
INFOID:0000000011497374
CAUTION:
Do not start engine while checking oil level.
1.
Remove filler plug (1).
2.
Fill with new oil to the specified level (A) near the filler plug hole.
3.
Clean threads of filler plug (1) and transfer case.
4.
Apply sealant to the threads of the filler plug (1), and install it. Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
MA-64, "Fluids and Lubricants"
.
: Front
ALDIA0383ZZ
: Front
ALDIA0382ZZ
: Front
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
ALDIA0383ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст