Nissan Qashqai J11. Manual — part 832
FRONT DRIVE SHAFT BOOT
FAX-15
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE (K9K)
RIGHT SIDE (MR16DDT)
1.
Cotter pin
2.
Drive shaft
3.
Plate
4.
Support bearing bracket
Refer to
E1DIA0233GB
1.
Cotter pin
2.
Drive shaft
3.
Plate
4.
Support bearing bracket
Refer to
E1DIA0513GB
1.
Cotter pin
2.
Drive shaft
3.
Plate
4.
Support bearing bracket
Refer to
FAX-16
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT BOOT
RIGHT SIDE (R9M)
DISASSEMBLY
LEFT SIDE
AWDIA1158ZZ
1.
Cotter pin
2.
Nut retainer
3.
Drive shaft
Refer to
for symbols in the figure.
JPDIF0047ZZ
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10. Damper band
11.
Dynamic damper
12. Circular clip
13. Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
FRONT DRIVE SHAFT BOOT
FAX-17
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE (R9M)
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000010432013
REMOVAL
1.
Remove tires from vehicle.
2.
Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Never pull on wheel sensor harness.
3.
Remove torque member mounting bolts. Hang torque member
not to interfere with work. Refer to
CAUTION:
Never depress brake pedal while brake caliper is removed.
AWDIA1159ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Stopper ring
9.
Spider assembly
10. Snap ring
11.
Housing
12. Dust shield
13. Support bearing
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
ALDIA0526ZZ
FAX-18
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT BOOT
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000010432013
REMOVAL
1.
Remove tires from vehicle.
2.
Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Never pull on wheel sensor harness.
3.
Remove torque member mounting bolts. Hang torque member
not to interfere with work. Refer to
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Put alignment marks (A) on disc brake rotor and wheel hub and
bearing. Remove disc brake rotor.
CAUTION:
Never drop the disc brake rotor.
5.
Remove cotter pin.
6.
Remove the nut retainer.
7.
Loosen the wheel hub lock nut from the drive shaft using power tool.
8.
Patch hub lock nut with a piece of wood. Hammer the wood to
disengage wheel hub and bearing assembly from drive shaft.
Remove the hub lock nut.
CAUTION:
• Never place the drive shaft joint at an extreme angle. Also
be careful not to overextend slide joint.
• Never allow the drive shaft to hang down without support-
for housing (or joint sub-assembly), shaft and the other
parts.
NOTE:
Use suitable puller if wheel hub and drive shaft cannot be sepa-
rated even after performing the above procedure.
9.
Remove the lower nut and bolt from the steering knuckle (shown in explode). Separate the transverse link
from the steering knuckle. Refer to
.
10. Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire.
10. Dust shield
11.
Support bearing
12. Plate
13. Support bearing bracket
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
ALDIA0526ZZ
JPDIG0066ZZ
JPDIG0070ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст