Nissan Qashqai J11. Manual — part 625
POSITION SWITCH
TM-75
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC/CIRCUIT DIAGNOSIS
POSITION SWITCH
BACK-UP LAMP SWITCH
BACK-UP LAMP SWITCH : Component Parts Location
INFOID:0000000010428763
BACK-UP LAMP SWITCH : Component Inspection
INFOID:0000000010428764
1.
CHECK BACK-UP LAMP SWITCH
Check continuity between position switch terminals with control lever
turned to 1st to 6th and reverse position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
.
PARK/NEUTRAL POSITION (PNP) SWITCH
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Parts Location
INFOID:0000000010428765
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Inspection
INFOID:0000000010428766
1.
CHECK PARK/NEUTRAL POSITION (PNP) SWITCH
1
: Position switch
E1DIA0340ZZ
Terminals
Gear position
Continuity
1 – 2
Reverse
Existed
Except reverse
Not existed
E1DIA0344GB
1
: Position switch
E1DIA0340ZZ
TM-76
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F95R]
POSITION SWITCH
Check continuity between position switch terminals with control lever
turned to 1st to 6th and reverse position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
Terminals
Gear position
Continuity
2 – 3
Neutral
Existed
Except neutral
Not existed
E1DIA0345GB
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
TM-77
< SYMPTOM DIAGNOSIS >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010428767
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
Reference page
SUSPECTED PARTS
(Possible cause)
OIL
(Oil
lev
e
l is
l
o
w
.)
OI
L (W
ro
ng
oi
l.
)
OIL
(Oil
lev
e
l is
h
igh
.)
GASKET
(Damaged)
OIL SEAL (W
orn or
damaged)
O-RING (W
orn
or
da
ma
ge
d)
SHIF
T CONTROL L
INKAGE
(W
o
rn)
SHIF
T FORK (W
o
rn)
GEAR (W
o
rn o
r da
m
age
d)
BEAR
ING
(W
orn
o
r
da
ma
ge
d)
BAUL
K
RING (W
orn
o
r da
ma
ge
d)
INSE
R
T
S
P
RING (Dam
ag
ed
)
Symptoms
Noise
1
2
3
3
Oil leakage
3
1
2
2
2
Hard to shift or will not shift
1
1
2
3
3
Jumps out of gear
1
2
2
TM-78
< PRECAUTION >
[6MT: RS6F95R]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Procedure without Cowl Top Cover
INFOID:0000000010497457
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Removing Battery Terminal
INFOID:0000000010508550
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
PIIB3706J
SEF289H
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст