Nissan Qashqai J11. Manual — part 610
POSITION SWITCH
TM-15
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC/CIRCUIT DIAGNOSIS
POSITION SWITCH
BACK-UP LAMP SWITCH
BACK-UP LAMP SWITCH : Component Parts Location
INFOID:0000000010288436
BACK-UP LAMP SWITCH : Component Inspection
INFOID:0000000010288437
1.
CHECK BACK-UP LAMP SWITCH
Check continuity between position switch terminals with control lever
turned to 1st to 6th and reverse position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
.
PARK/NEUTRAL POSITION (PNP) SWITCH
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Parts Location
INFOID:0000000010288438
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Inspection
INFOID:0000000010288439
1.
CHECK PARK/NEUTRAL POSITION (PNP) SWITCH
1
: Position switch
JPDIC0070ZZ
Terminals
Gear position
Continuity
1 – 2
Reverse
Existed
Except reverse
Not existed
PCIB1781E
1
: Position switch
JPDIC0070ZZ
TM-16
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F94R]
POSITION SWITCH
Check continuity between position switch terminals with control lever
turned to 1st to 6th and reverse position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
Terminals
Gear position
Continuity
2 – 3
Neutral
Existed
Except neutral
Not existed
JPDIC0091ZZ
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
TM-17
< SYMPTOM DIAGNOSIS >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010288440
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
Reference page
SUSPECTED PARTS
(Possible cause)
OIL
(Oil
lev
e
l is
l
o
w
.)
OI
L (W
ro
ng
oi
l.
)
OIL
(Oil
lev
e
l is
h
igh
.)
GASKET
(Damaged)
OIL SEAL (W
orn or
damaged)
O-RING (W
orn
or
da
ma
ge
d)
SHIF
T CONTROL L
INKAGE
(W
o
rn)
SHIF
T FORK (W
o
rn)
GEAR (W
o
rn o
r da
m
age
d)
BEAR
ING
(W
orn
o
r
da
ma
ge
d)
BAUL
K
RING (W
orn
o
r da
ma
ge
d)
INSE
R
T
S
P
RING (Dam
ag
ed
)
Symptoms
Noise
1
2
3
3
Oil leakage
3
1
2
2
2
Hard to shift or will not shift
1
1
2
3
3
Jumps out of gear
1
2
2
TM-18
< PRECAUTION >
[6MT: RS6F94R]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Procedure without Cowl Top Cover
INFOID:0000000010497458
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Service Notice or Precautions for Manual Transaxle
INFOID:0000000010288441
CAUTION:
• If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Return CSC insert to original position to remove transaxle assembly. Dust on clutch disc sliding
parts may damage seal of CSC and may cause clutch fluid leakage.
• Never reuse transaxle gear oil, once it has been drained.
• Check oil level or replace gear oil with vehicle on level surface.
• During removal or installation, keep inside of transaxle clear of dust or dirt.
• Check for the correct installation status prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts they are applied.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, use it.
• Never damage sliding surfaces and mating surfaces.
Precautions for Removing Battery Terminal
INFOID:0000000010508552
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
PIIB3706J
SEF289H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст