Nissan Qashqai J11. Manual — part 611
PRECAUTIONS
TM-19
< PRECAUTION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
TM-20
< PREPARATION >
[6MT: RS6F94R]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010288442
Tool number
Tool name
Description
KV381054S0
Puller
Removing mainshaft front bearing outer race
KV38100200
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
• Installing mainshaft front bearing outer race
• Installing mainshaft rear bearing outer race
• Installing differential side bearing outer race
(clutch housing side)
ST33220000
Drift
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.
Installing input shaft oil seal
ST33400001
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
Installing differential side bearing outer race
(transaxle case side)
KV38100300
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
Installing differential side oil seal
ST36720030
Drift
a: 70 mm (2.76 in) dia.
b: 40 mm (1.57 in) dia.
c: 29 mm (1.14 in) dia.
• Installing input shaft rear bearing
• Installing mainshaft front bearing inner race
ZZA0601D
ZZA1143D
ZZA1046D
ZZA0814D
ZZA1046D
ZZA0978D
PREPARATION
TM-21
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ST33052000
Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
• Removing mainshaft rear bearing inner race
• Removing 6th main gear
• Removing 5th main gear
• Removing 4th main gear
• Removing 1st main gear
• Removing 1st-2nd synchronizer assembly
• Removing 2nd main gear
• Removing bushing
• Removing 3rd main gear
• Removing mainshaft front bearing inner
race
KV32102700
Drift
a: 54 mm (2.13 in) dia.
b: 32 mm (1.26 in) dia.
• Installing bushing
• Installing 2nd main gear
• Installing 3rd main gear
• Installing 4th main gear
• Installing 5th main gear
• Installing 6th main gear
ST30901000
Drift
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
Installing mainshaft rear bearing inner race
ST33061000
Drift
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
Removing differential side bearing inner race
(clutch housing side)
KV32300QAM
(Renault SST: B.vi 1823)
Drift
Removing and installing input shaft rear bear-
ing mounting bolt
Tool number
Tool name
Description
ZZA0969D
S-NT065
ZZA0978D
ZZA0969D
PCIB2078J
TM-22
< PREPARATION >
[6MT: RS6F94R]
PREPARATION
Commercial Service Tools
INFOID:0000000010288443
Tool name
Description
Socket
a: 8 mm (0.31 in)
b: 5 mm (0.20 in)
Removing and installing drain plug
Spacer
a: 25 mm (0.98 in) dia.
b: 25 mm (0.98 in)
Removing mainshaft front bearing outer race
Drift
a: 17 mm (0.67 in) dia.
• Installing bushing
• Installing shifter lever oil seal
• Installing selector lever oil seal
Drift
a: 35 mm (1.38 in) dia.
b: 25 mm (0.98 in) dia.
Installing input shaft front bearing
Drift
a: 24 mm (0.94 in) dia.
Removing input shaft rear bearing
Drift
a: 43 mm (1.69 in) dia.
• Removing differential side bearing inner
race (transaxle case side)
• Installing input shaft rear bearing
PCIB1776E
PCIB1780E
S-NT063
S-NT065
PCIB1779E
NT109
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст