Nissan Qashqai J11. Manual — part 427
ECK-268
< DTC/CIRCUIT DIAGNOSIS >
[K9K]
P0606 ECM
P0606 ECM
DTC Logic
INFOID:0000000010289869
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DIAGNOSIS PROCEDURE
NOTE:
DTC P0606 can not duplicate.
>> Proceed to
ECK-268, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010289870
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Turn ignition switch OFF and wait for 20 seconds.
4.
Turn ignition switch ON and perform the self-diagnosis.
Is the DTC P0606 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
Replace ECM. Refer to
ECK-399, "Removal and Installation"
.
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P0606
COMPUTER
(Control module processor)
• 1.DEF: SYSTEM INTERNAL
FAILURE
Internal error.
ECM
P060A ECM
ECK-269
< DTC/CIRCUIT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
ECK
N
P
O
P060A ECM
DTC Logic
INFOID:0000000010289873
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECK-269, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010289874
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Turn ignition switch OFF and wait for 1 minute.
4.
Turn ignition switch ON and wait at least 1 second.
5.
Perform the self-diagnosis.
Is the DTC P060A displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P060A
COMPUTER
(Internal control module monitoring
processor performance)
• 1.DEF: —
• 2.DEF: JAMMED ACCELERA-
TOR PEDAL DETECTED
• 3.DEF: IMPLAUSIBLE SIGNAL
• 4.DEF: JAMMED ACCELERA-
TOR PEDAL DETECTED
Internal monitoring processor error.
ECM
ECK-270
< DTC/CIRCUIT DIAGNOSIS >
[K9K]
P060B ECM
P060B ECM
DTC Logic
INFOID:0000000010289875
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECK-270, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010289876
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Turn ignition switch OFF and wait for 20 seconds.
4.
Turn ignition switch ON and perform the self-diagnosis.
Is the DTC P060B displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM. Refer to
ECK-399, "Removal and Installation"
.
2.
Go to
.
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P060B
COMPUTER
(Internal control module A/D processing
performance)
• 1.DEF: —
Internal A/D processor error.
• ECM
P061A ECM
ECK-271
< DTC/CIRCUIT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
ECK
N
P
O
P061A ECM
DTC Logic
INFOID:0000000010289877
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DIAGNOSIS PROCEDURE
NOTE:
DTC P061A can not duplicate.
>> Proceed to
ECK-271, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010289878
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Turn ignition switch OFF and wait for 1 minute.
4.
Turn ignition switch ON and wait at least 1 second.
5.
Perform the self-diagnosis.
Is the DTC P061A displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P061A
COMP
(Internal control module torque
performance)
• 1.DEF: SIGNAL INCOHER-
ENCE
• 2.DEF: —
• 3.DEF: —
• 4.DEF: FAULT ALERTED VIA
THE CONTROL UNIT
• 5.DEF: —
• 6.DEF: —
ECM detects internal error.
ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст