Nissan Qashqai J11. Manual — part 643

AIR BREATHER HOSE

TM-147

< REMOVAL AND INSTALLATION >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AIR BREATHER HOSE

Exploded View

INFOID:0000000010288507

Removal and Installation

INFOID:0000000010288508

REMOVAL

Refer to the figure for removal procedure.

INSTALLATION

Refer to the figure for installation procedure.

CAUTION:

• Make sure there are no pinched or restricted areas on the air breather hose caused by bending or

winding when installing it.

• Be sure to insert air breather hose into air breather tube until

hose end reaches the tube's base.

• Set air breather hose with painted mark facing forward.
• Install air breather hose to air cleaner case by fully inserting

the clip.

1.

Air breather hose

2.

Transaxle assembly

3.

Air breather tube

4.

Clamp

5.

Air cleaner case

: Vehicle front

JPDIC0051ZZ

SCIA2663J

TM-148

< UNIT REMOVAL AND INSTALLATION >

[6MT: RS6F52A]

TRANSAXLE ASSEMBLY

UNIT REMOVAL AND INSTALLATION

TRANSAXLE ASSEMBLY

Exploded View

INFOID:0000000010288509

R9M

CAUTION:

If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder). Return CSC insert to orig-
inal position to remove transaxle assembly. Dust on clutch disc sliding parts may damage seal of CSC and may cause clutch
fluid leakage.

Removal and Installation

INFOID:0000000010288510

CAUTION:

If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Return CSC insert to original position to remove transaxle assembly. Dust on clutch disc sliding parts
may damage seal of CSC and may cause clutch fluid leakage.

REMOVAL

1.

Disconnect the battery cable from the negative terminal.

2.

Remove air breather hose. Refer to

TM-147, "Removal and Installation"

.

3.

Remove air cleaner case and air duct (inlet). Refer to

EM-380, "Removal and Installation"

(R9M).

4.

Remove battery. Refer to

PG-155, "Removal and Installation"

.

5.

Disconnect connectors (A) and then remove bracket (1).

6.

Drain clutch fluid and then remove clutch tube from CSC (Con-
centric Slave Cylinder). Refer to

CL-17, "Removal and Installa-

tion"

.

CAUTION:

Never depress clutch pedal during removal procedure.

7.

Disconnect park/neutral position (PNP) switch harness connec-
tor.

8.

Disconnect back-up lamp switch harness connector.

9.

Disconnect ground cable.

10. Remove wire harnesses from transaxle assembly.

JPDIC0126GB

1.

Transaxle assembly

: For the tightening torque, refer to “INSTALLATION”.

Refer to

GI-4, "Components"

for symbols not described on the above.

JPDIA0240ZZ

TRANSAXLE ASSEMBLY

TM-149

< UNIT REMOVAL AND INSTALLATION >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

11. Disconnect select cable and shift cable from transaxle assembly. Refer to

TM-143, "Removal and Installa-

tion"

.

12. Remove starter motor. Refer to

STR-32, "R9M : Removal and Installation"

.

13. Remove engine under cover.

14. Cap or plug transmission assembly opening(s) to prevent fluid from spilling.
15. Remove exhaust front tube. Refer to

EX-22, "Removal and Installation"

(R9M).

16. Remove propeller shaft assembly (for 4WD). Refer to

DLN-186, "Removal and Installation"

.

17. Remove front drive shafts. Refer to

FAX-60, "Removal and Installation (LH)"

(4WD), or

FAX-63, "Removal

and Installation (RH)"

(4WD).

NOTE:
Insert a suitable plug into differential side oil seal after removing front drive shaft.

18. Remove transfer assembly (for 4WD). Refer to

DLN-155, "Removal and Installation"

.

19. Remove rear engine mounting brackets and rear torque rod. Refer to

EM-431, "Removal and Installation"

.

20. Remove suspension member and suspension member stay. Refer to

FSU-21, "Removal and Installation"

.

21. Set a suitable jack to transaxle assembly and then set a suitable jack to engine assembly.

CAUTION:

When setting a suitable jack, be careful so that it does not contact with the switch.

22. Remove transaxle assembly mounting bolts or nuts.
23. Remove engine mounting through bolt-securing nut . Refer to

EM-431, "Removal and Installation"

.

24. Remove two mounting bolts of engine mounting insulator (LH) (for R9M). Refer to

EM-431, "Removal and

Installation"

.

25. Remove transaxle assembly from the vehicle.

CAUTION:

• Secure transaxle assembly to a suitable jack while removing it.
• The transaxle assembly must not interfere with the wire harnesses and clutch tube.

26. Remove CSC (Concentric Slave Cylinder). Refer to

CL-17, "Removal and Installation"

.

CAUTION:

If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylin-
der). Return CSC insert to original position to remove transaxle assembly. Dust on clutch disc
sliding parts may damage seal of CSC and may cause clutch fluid leakage.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Tighten transaxle assembly mounting bolts to the specified torque. The figure is the view from the engine.
- R9M

*: Nut and stud

CAUTION:

• The transaxle assembly must not interfere with the wire harnesses and clutch tube.
• When installing transaxle assembly, never bring input shaft into contact with clutch cover.
• Refer to

CL-17, "Removal and Installation"

for CSC (Concentric Slave Cylinder) installation procedure.

• Refer to

TM-143, "Removal and Installation"

for select cable and shift cable installation procedure.

• Bleed the air from the clutch hydraulic system. Refer to

CL-8, "Air Bleeding Procedure"

.

• After installation, check for oil leakage and oil level. Refer to

TM-140, "4WD : Inspection"

.

: Transaxle to engine

: Engine to transaxle

Bolt and nut symbol

A*

B

C

Quantity

2

4

3

Bolt length

“

” mm (in)

—

60 (2.36)

55 (2.17)

Tightening torque
N·m (kg-m, ft-lb)

48 (4.9, 35)

JPDIC0128ZZ

TM-150

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52A]

TRANSAXLE ASSEMBLY

UNIT DISASSEMBLY AND ASSEMBLY

TRANSAXLE ASSEMBLY

4WD

4WD : Exploded View

INFOID:0000000010288515

CASE AND HOUSING

SHAFT AND GEAR

1.

Differential side oil seal

2.

Clutch housing

3.

Input shaft oil seal

4.

Oil channel

5.

Oil gutter A

6.

Back-up lamp switch

7.

Plunger

8.

Gasket

9.

Plug

10. Bore plug

11. Striking rod oil seal

12. Transaxle case

13. Oil gutter B

14. Filler plug

15. Air breather tube

16. Park/Neutral position (PNP) switch

17. Shifter lever oil seal

18. Drain plug

19. Magnet

: Apply Genuine Liquid Gasket, Three Bond 1215 or an equivalent.

Refer to

GI-4, "Components"

for symbols not described on the above.

JPDIC0045GB