Nissan Qashqai J11. Manual — part 2129
AV
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
AV-205
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE
1.
Connect around view monitor control unit and LH side camera connectors.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit connector M8 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
3.
CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and LH side camera connectors.
3.
Check continuity between around view monitor control unit connector M8 and LH side camera connector
D3.
4.
Check continuity between around view monitor control unit connector M8 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK LH SIDE CAMERA IMAGE SIGNAL
1.
Connect around view monitor control unit and LH side camera connectors.
2.
Turn ignition switch ON.
3.
Check signal between the terminals of around view monitor control unit connector M8.
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M8
56
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M8
56
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
M8
59
D3
16
Yes
60
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M8
59
No
AV-206
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
NO
>> Replace LH side camera. Refer to
AV-269, "Removal and Installation"
.
Around view monitor control unit connector M8
Condition
Reference value
(+)
(
−
)
Terminal
Terminal
59
60
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV
U112F EPS CIRCUIT
AV-207
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U112F EPS CIRCUIT
DTC Logic
INFOID:0000000010944762
DTC DETECTION LOGIC
POSSIBLE CAUSE
EPS
FAIL-SAFE
Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON
2.
Perform “All DTC Reading” with CONSULT.
3.
Check if the “U112F” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
“U112F” detected as the current malfunction?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010944763
1.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if the “U1000” is detected other than “U112F” in “Self Diagnostic Result” of “AVM”.
“U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-189, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
.
NO
>> GO TO 2.
2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if any DTC is detected in “Self Diagnostic Result” of “EPS/DAST3”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the around view monitor control unit. Refer to
AV-267, "Removal and Installation"
DTC
Trouble diagnosis
(Trouble diagnosis contents)
DTC detecting condition
U112F
EPS CIRC
(EPS circuit)
The around view monitor control unit detects that EPS has a malfunction.
AV-208
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U1217 AV CONTROL UNIT
U1217 AV CONTROL UNIT
DTC Logic
INFOID:0000000010435698
DTC DETECTION LOGIC
CONSULT Display
DTC Detection Condition
Possible Cause
BLUETOOTH MODULE
[U1217]
Connection failure to the internal Blueooth
®
sub
unit is detected.
Replace AV control unit if malfunction occurs
constantly.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст