Nissan Qashqai J11. Manual — part 983
STEERING WHEEL
ST-7
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
BASIC INSPECTION
STEERING WHEEL
Inspection
INFOID:0000000010438961
NEUTRAL POSITION STEERING WHEEL
1.
Check that steering gear assembly, steering column assembly and steering wheel are installed in the cor-
rect position.
2.
Check wheel alignment within specification. Refer to
FSU-7, "Wheel Alignment Inspection"
.
3.
Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.
• Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.
CAUTION:
If the adjustment is performed by using the inner socket, check wheel alignment after the adjust-
ment. Refer to
ST-8
< REMOVAL AND INSTALLATION >
STEERING WHEEL
REMOVAL AND INSTALLATION
STEERING WHEEL
Exploded View
INFOID:0000000010438964
Removal and Installation
INFOID:0000000010438965
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1.
Set vehicle to the straight-ahead position.
2.
Remove driver air bag module. Refer to
SR-14, "Removal and Installation"
.
3.
Remove steering wheel bolt after steering is locked.
CAUTION:
Never reuse steering wheel lock bolt.
4.
Disconnect harness connector.
1.
Steering wheel
Refer to
for symbols in the figure.
AWGIA0318ZZ
STEERING WHEEL
ST-9
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
5.
Remove steering wheel with the steering wheel puller (A) (SST:
ST27180001).
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
CAUTION:
• Never twist spiral cable excessively after it becomes tight. (Twisting may cause the cable to be torn
off.)
• Never reuse steering wheel lock bolt.
SGIA1524J
ST-10
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
Exploded View
INFOID:0000000010438966
Removal and Installation
INFOID:0000000010438967
CAUTION:
• While removing the steering column assembly, never unlock the tilt lever.
• Never impact on the axis when removing steering column assembly.
• Be careful when removing steering column assembly from the vehicle because it is heavy.
• Keep steering column assembly away from magnetic sources.
• Never disassemble steering column assembly. It is not separable.
• While removing the steering column assembly, never move the steering gear.
• When removing the steering column assembly, be careful not to allow the intermediate shaft to turn.
REMOVAL
1.
Set vehicle to the straight-ahead position.
2.
Place the tilt to the highest level.
3.
Remove combination switch. Refer to
MWI-80, "Removal and Installation"
4.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
5.
Disconnect each switch harness connectors installed to steering column assembly.
6.
Remove bolt and separate steering column from steering gear pinion shaft.
CAUTION:
Never move the steering gear during removal and installation of the steering column.
7.
Remove nuts and remove steering column.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
Steering column
2.
Floor cover
3.
Floor seal
Refer to
for symbols in the figure.
E1GIA0093GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст