Nissan Qashqai J11. Manual — part 769
CVT OIL WARMER
TM-651
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000010248026
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid and engine coolant.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to Refer to
.
TM-652
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
PLUG
PLUG
Description
INFOID:0000000010245711
Replace the O-ring if oil leakage or exudes from the plug.
Exploded View
INFOID:0000000010245712
Removal and Installation
INFOID:0000000010245713
REMOVAL
1.
Remove front fender protector (LH). Refer to
.
2.
Remove the plug and O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection and Adjustment
INFOID:0000000010245714
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Transaxle assembly
O-ring
Plug
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply CVT fluid
JSDIA5136GB
TRANSAXLE ASSEMBLY
TM-653
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000010245715
Removal and Installation
INFOID:0000000010245716
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
• Perform when the engine is cold.
• When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and
then replace the TCM. Refer to
.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
Transaxle assembly
O-ring
CVT fluid charging pipe
Bracket
CVT fluid charging pipe cap
Stud bolt B
Stud bolt A
: For the tightening torque, refer to
TM-653, "Removal and Installation"
.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply petroleum jelly
JSDIA5226GB
TM-654
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
TRANSAXLE ASSEMBLY
1.
Remove engine and transaxle assembly. Refer to
EM-431, "Removal and Installation"
2.
Remove the CVT water hoses from transmission side. Refer to
.
3.
Turn crankshaft, and remove the tightening nuts for drive plate and torque converter.
CAUTION:
Rotate crankshaft clockwise (as viewed from the crankshaft pulley side).
4.
Remove the bolts that fasten the transaxle assembly and engine assembly.
5.
Separate the engine from the transaxle assembly.
NOTE:
Using paint, put matching marks on the drive plate and torque converter when removing the torque con-
verter to drive plate nuts.
6.
Remove following parts from transaxle assembly.
• Air breather hose (Refer to
• Charging pipe and O-ring
INSTALLATION
Note the followings and installation is in the reverse order of removal.
NOTE:
Write down the serial number of the new transaxle assembly.
CAUTION:
• When replacing an engine or transaxle you must make sure any dowels are installed correctly during
re-assembly
• Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of drive
train components.
• Never reuse O-rings or copper sealing washers.
• When turning crankshaft, turn it clockwise as viewed from the front of the engine.
• When tightening the nuts for the torque converter while securing the crankshaft pulley bolt, be sure
to confirm the tightening torque of the crankshaft pulley bolt. Refer to
.
• After converter is installed to drive plate, rotate crankshaft several turns to check that CVT rotates
freely without binding.
• When installing the CVT to the engine, align the matching mark on the drive plate with the matching
mark on the torque converter.
• When installing the drive plate to torque converter nuts, tighten them temporarily. then tighten the nuts to the
specified torque.
• Install the transaxle assembly and engine assembly mounting bolts according to the following standards.
JSDIA4208GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст