Nissan Qashqai J11. Manual — part 1309
FUEL FILLER LID OPENER
DLK-505
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000010479398
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000010479399
REMOVAL
1.
Fully open fuel filler lid assembly.
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
JMKIB3263ZZ
DLK-506
< REMOVAL AND INSTALLATION >
[TYPE 3]
FUEL FILLER LID OPENER
2.
Remove fuel mounting pin (1).
3.
Remove fixing screws, and then remove fuel filler lid assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the fixing screws.
• Apply anti-corrosion wax to mounting surface of fixing screw and fuel filler lid to prevent rust.
NOTE:
The following table shows the specified values for checking normal installation status.
Unit: mm [in]
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000010479400
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage lower finisher RH. Refer to
.
3.
In the order of 1
→
2 as shown in the figure, rotate and disengage
fuel filler lid lock assembly, and then remove fuel filler lid lock
assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
In the order of 1
→
4 as shown in the figure. Disengage fuel filler
lid opener cable (1). Remove fuel filler lid opener cable while
pressing stopper pin (2).
JMKIB3183ZZ
Clearance
Evenness
Fuel filler lid – Body side outer
3.7 – 5.3
(0.146 – 0.209)
(-1.0) – (+1.0)
[(-0.039) – (+0.039)]
: Pawl
: Vehicle front
JMKIB1094ZZ
JMKIA5719ZZ
FUEL FILLER LID OPENER
DLK-507
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000010479401
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner RH and rear kicking plate inner RH. Refer to
.
4.
Remove dash side finisher RH. Refer to
INT-18, "Removal and Installation"
5.
Remove center pillar lower garnish RH. Refer to
INT-18, "Removal and Installation"
.
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse cable protector. Always replace it with a new one when it is removed.
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
JMKIA5672ZZ
DLK-508
< REMOVAL AND INSTALLATION >
[TYPE 3]
DOOR SWITCH
DOOR SWITCH
Removal and Installation
INFOID:0000000010435109
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2173ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст