Nissan Qashqai J11. Manual — part 2149
DAS-10
< PRECAUTION >
[DRIVER ASSISTANCE SYSTEM]
PRECAUTIONS
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Precaution for Work
INFOID:0000000010416770
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
DAS
PRECAUTIONS
DAS-11
< PRECAUTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Precaution for LDW System Service
INFOID:0000000010868543
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Never perform the active test while driving.
• Never change LDW initial state ON
⇒
OFF without the consent of the customer.
Precaution for BSW System Service
INFOID:0000000010868544
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Never perform the active test while driving.
• Never change BSW initial state ON
⇒
OFF without the consent of the customer.
Precautions for Driver Assistance Systems
INFOID:0000000010619951
CAUTION:
• Do not use or disassemble the distance sensor removed from the vehicle.
• Erase DTC when replacing parts of FEB system, then check the operation of FEB system after align-
ment, if necessary.
WARNING:
Be cautious of traffic conditions and other vehicles when performing a road test.
CAUTION:
• Do not use the DAS system when driving with free rollers or on a chassis dynamometer.
• Do not disassemble or alter the rear view camera.
• Do not disable the DAS system without the consent of the customer.
OBSERVE THE FOLLOWING ITEMS IN ORDER TO KEEP THE DAS SYSTEM OPERATING PROP-
ERLY:
Rear view Camera Maintenance
The rear view camera for the DAS system is located in the back door. To keep the DAS system operating
properly and prevent a malfunction, be sure to observe the following:
• Always keep the camera lens area clean.
• Do not attach bumper stickers (including transparent materials) or install an accessory near the rear view-
camera.
• Do not strike or damage the areas around the rear view camera.
• Do not touch the camera lens (except for cleaning) or remove the rear view camera.
DAS-12
< PREPARATION >
[DRIVER ASSISTANCE SYSTEM]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010416774
NOTE:
For radar alignment, KV99112700 or a set of Kent-Moore No. SST are to be used.
Tool number
(SPX - North America No.)
Tool name
Description
KV99112700
(—)
ICC target board
Uses for radar alignment
JSOIA1012ZZ
DAS
COMPONENT PARTS
DAS-13
< SYSTEM DESCRIPTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010416775
JMOIA0021ZZ
No.
Component
Function
Front camera unit
• Front camera unit is installed above the inside mirror.
• Detects the lane marker, the lighting condition in front of the vehicle and traffic sign in
travel lane.
Blind spot warning indictor RH
• Installed on the front door corner finisher, the blind spot warning indicator warns the
driver by lighting/blinking.
• Receives a blind spot warning indicator operation signal from the around view monitor
control unit.
Sonar control unit
• The warning buzzer outputs by inputting the sensor signal from sonar sensors.
• Sensor signal that corresponds to the detected distance to an obstacle is transmitted to
around view monitor control unit via can communication.
• Refer to
SN-58, "Component Parts Location"
for detailed installation location.
Around view monitor control unit
• The around view monitor control unit is installed behind the glove box.
• Vehicle width guide lines, predicted course line, vehicle front guiding line and vehicle
side line, and vehicle icon are displayed and combined with camera images.
ABS actuator and electric unit (con-
trol unit)
• Transmits the vehicle speed signal (wheel speed) to around view monitor via CAN com-
munication
• Refer to
BRC-8, "Component Parts Location"
for detailed installation location.
Rear view camera washer motor
Pumps washer fluid to the rear view camera.
Distance sensor
• Distance sensor is installed to the back of the front bumper and detects a vehicle ahead
by using millimeter waves.
• Distance sensor detects radar reflected from a vehicle ahead by irradiating radar for-
ward and calculates a distance from the vehicle ahead and relative speed, based on
the detected signal.
• Distance sensor transmits the presence/absence of vehicle ahead and the distance
from the vehicle to around view monitor control unit via CAN communication.
TCM
Refer to
TM-217, "CVT CONTROL SYSTEM : Component Parts Location"
(RE0F10D) or
TM-430, "CVT CONTROL SYSTEM : Component Parts Location"
(RE0F10G) for detailed
installation location.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст