Nissan Qashqai J11. Manual — part 529
EC9-272
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0697 SENSOR POWER SUPPLY
YES
>> GO TO 3.
NO
>> Repair short to ground or short to power in harness or connectors.
3.
CHECK COMPONENTS
Check the following.
• Crankshaft position sensor. Proceed to
EC9-227, "Component Inspection (Crankshaft Position Sensor)"
• Fuel rail pressure sensor. Proceed to
EC9-209, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace malfunctioning component.
P0833 CPP SWITCH
EC9-273
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
P0833 CPP SWITCH
DTC Logic
INFOID:0000000010309247
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-1
1.
Turn ignition switch ON.
2.
Fully depress clutch pedal.
3.
Fully release clutch pedal.
4.
Repeat steps 2 and 3 for five times.
5.
Check DTC.
Is DTC detected?
YES
>> Go to
EC9-274, "Diagnosis Procedure"
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-2
Perform component function check. Refer to
EC9-273, "Component Function Check"
.
NOTE:
Use component function check to check the overall function of the clutch switch circuit. During this
check, a DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
EC9-274, "Diagnosis Procedure"
Component Function Check
INFOID:0000000010309248
1.
PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0833
CLUTCH SWITCH SIGNAL
CONSISTENCY
(Clutch pedal switch “B” cir-
cuit)
• 1.DEF: SIGNAL INCOHER-
ENCE
• 2.DEF: —
Correlation of two clutch pedal position switch signal
is inconsistency.
• Harness and connectors
• Clutch pedal position switch
ECM
Condition
Voltage
Connector
+
–
Terminal
E58
9
29
Clutch pedal
Fully released
Approx. 0 V
Fully depressed
Battery voltage
EC9-274
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0833 CPP SWITCH
NO
>> Proceed to
EC9-274, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010309249
1.
CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT
1.
Disconnect clutch pedal position switch harness connector.
2.
Check the continuity between clutch pedal position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair open circuit or short to power in harness or connectors.
2.
CHECK CLUTCH PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connectors.
2.
Check the continuity between clutch pedal position switch harness connector and ECM harness connec-
tor.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK CLUTCH PEDAL POSITION SWITCH
EC9-274, "Component Inspection (Clutch Pedal Position Switch)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace clutch pedal position switch.
Component Inspection (Clutch Pedal Position Switch)
INFOID:0000000010309250
1.
CHECK CLUTCH PEDAL POSITION SWITCH-1
1.
Turn ignition switch OFF.
2.
Disconnect clutch pedal position switch harness connector.
3.
Check the continuity between clutch pedal position switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK CLUTCH PEDAL POSITION SWITCH-2
+
-
Continuity
Clutch pedal position switch
Connector
Terminal
E2
2
Ground
Existed
+
-
Continuity
Clutch pedal position switch
ECM
Connector
Terminal
Connector
Terminal
E2
1
E58
9
Existed
Clutch pedal position switch
Condition
Continuity
+
-
Terminal
1
2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
P0833 CPP SWITCH
EC9-275
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
1.
Adjust clutch pedal position switch installation. Refer to
.
2.
Check the continuity between clutch pedal position switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace clutch pedal position switch.
Clutch pedal position switch
Condition
Continuity
+
-
Terminal
1
2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст