Nissan Qashqai J11. Manual — part 763
AIR BREATHER HOSE
TM-627
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000010245685
Removal and Installation
INFOID:0000000010245686
REMOVAL
1.
Remove the air duct (inlet), air cleaner cases assembly with mass air flow sensor, and air duct assembly.
Refer to
EM-380, "Removal and Installation"
2.
Remove air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never bend the air breather hose to prevent damage to the hose.
• Insert air breather hose to the end of air breather.
• Insert air breather hose
to air breather tube
all the way to
the curve of the tube.
• Insert air breather hose to air breather tube so that the paint
mark
is facing upward.
Air breather hose cap
Air breather hose
Breather tube
Transaxle assembly
JSDIA5220ZZ
JSDIA5387ZZ
TM-628
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
G SENSOR
G SENSOR
Exploded View
INFOID:0000000010249395
Removal and Installation
INFOID:0000000010249396
CAUTION:
• Never drop or strike G sensor, because it has little tolerance for impact.
• Never use a power tool to avoid impact.
REMOVAL
1.
Turn ignition switch OFF.
2.
Remove center console. Refer to
IP-19, "Removal and Installation"
3.
Disconnect G sensor harness connector.
4.
Remove G sensor mounting nuts and remove G sensor.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000010249397
ADJUSTMENT AFTER INSTALLATION
Perform “CALIBRATION OF G SENSOR”. Refer to
G sensor
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5228GB
OIL PAN
TM-629
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000010245687
COMPONENT PARTS LOCATION
Removal and Installation
INFOID:0000000010245688
REMOVAL
1.
Remove drain plug
from oil pan and then drain the CVT fluid.
Transaxle assembly
Oil pan gasket
Oil pan
Drain plug
Drain plug gasket
Magnet
Overflow plug
O-ring
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA4194GB
JSDIA5205ZZ
TM-630
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
OIL PAN
2.
Remove drain plug gasket
.
3.
Remove oil pan bolts (
).
4.
Remove oil pan from transaxle case.
5.
Remove oil pan gasket
from oil pan.
6.
Remove magnets
from oil pan.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket.
• Never reuse drain plug gasket.
• Never reuse O-ring.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
• Install the oil pan to the transaxle case with the following procedure.
1.
Install the oil pan gasket to the oil pan.
CAUTION:
JSDIA5206ZZ
: Vehicle front
JSDIA5207ZZ
JSDIA5208ZZ
JSDIA5209ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст