Nissan Qashqai J11. Manual — part 103
CYLINDER BLOCK
EM-351
< UNIT DISASSEMBLY AND ASSEMBLY >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Check that the difference between the largest and the smallest diameters in the same vertical plane of each
diameter of each cylinder barrel is within the taper tolerance.
CRANKSHAFT MAIN JOURNAL DIAMETER
Use micrometer to measure crankshaft main journal diameter.
CRANKSHAFT PIN JOURNAL DIAMETER
Use micrometer to measure crankshaft pin journal diameter.
FLYWHEEL ISNPECTION
For a dual mass flywheel which has worked: presence of a free rotation angle. This angle is measured by fix-
ing the primary flywheel and turning the secondary flywheel. The dual mass flywheel free rotation angle must
not exceed 15
°
or 3 cm in linear movement measured on the edge.
Maximum tapper permitted
0.01 mm (0.0004 in)
Standard
: Refer to
FEM114
Standard
: Refer to
PBIC0127E
EM-352
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000010282107
GENERAL SPECIFICATIONS
Drive Belt
INFOID:0000000010282108
DRIVE BELT
Camshaft
INFOID:0000000010282109
CAMSHAFT
Unit: mm (in)
Cylinder arrangement
In-line 4
Displacement
cm
3
(cu in)
1.461 (89.15)
Bore and stroke
mm (in)
76 x 80.5 (2.99 x 3.17)
Valve arrangement
SOHC
Firing order
1-3-4-2
Number of piston rings
Compression
2
Oil
1
Number of main bearings
5
Compression ratio
15.2
Compression pressure
kPa (bar, kg/cm
2
, psi)
Maximum pressure must be at least 1,800
(18, 18.36, 261)
Valve timing
a
b
c
d
e
f
200
°
191
°
-9
°
20
°
-7
°
27
°
PBIC0187E
Tension of drive belt
Auto adjustment by auto-tensioner
Items
Standard
Camshaft bracket inner diameter
No. 1, 2, 3, 4, 5
25.04 - 25.06 (0.9858 - 0.9866)
No. 6
28.04 - 28.06 (1.1039 - 1.1047)
Camshaft journal diameter
No. 1, 2, 3, 4, 5
24.979 - 25.000 (0.9834 - 0.9843)
No. 6
27.979 - 28.000 (1.1015 - 1.1024)
Camshaft end play
0.080 - 0.178 (0.0031 - 0.0070)
Camshaft runout
Less than 0.05 (0.0020)
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-353
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
VALVE LIFTER
Unit: mm (in)
VALVE CLEARANCE
Unit: mm (in)
AVAILABLE VALVE LIFTER
Unit: mm (in)
Camshaft cam height “A”
Intake
44.012 - 44.018 (1.7327 - 1.7329)
Exhaust
44.592 - 44.598 (1.7555 - 1.7557)
Items
Standard
SEM671
Items
Standard
Valve lifter outer diameter
34.965 - 34.985 (1.3767 - 1.3774)
Valve lifter hole diameter
35.000 - 35.040 (1.3780 - 1.3795)
Valve lifter clearance
0.015 - 0.075 (0.0006 - 0.0030)
Items
Cold
Intake
0.125 - 0.250 (0.0049 - 0.0098)
Exhaust
0.325 - 0.450 (0.0128 - 0.0177)
Part number
Thickness
13229BN700
7.550 (0.2972)
13229BN701
7.575 (0.2982)
13229BN702
7.600 (0.2992)
13229BN703
7.625 (0.3002)
13229BN704
7.650 (0.3012)
13229BN705
7.675 (0.3022)
13229BN706
7.700 (0.3031)
13229BN707
7.725 (0.3041)
13229BN708
7.750 (0.3051)
13229BN709
7.775 (0.3061)
13229BN710
7.800 (0.3071)
13229BN711
7.825 (0.3081)
13229BN712
7.850 (0.3091)
13229BN713
7.875 (0.3100)
13229BN714
7.900 (0.3110)
13229BN715
7.925 (0.3120)
13229BN716
7.950 (0.3130)
13229BN717
7.975 (0.3140)
EM-354
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
SERVICE DATA AND SPECIFICATIONS (SDS)
Cylinder Head
INFOID:0000000010282110
CYLINDER HEAD
Unit: mm (in)
VALVE DIMENSIONS
13229BN718
8.000 (0.3150)
13229BN719
8.025 (0.3159)
13229BN720
8.050 (0.3169)
13229BN721
8.075 (0.3179)
13229BN722
8.100 (0.3189)
13229BN723
8.125 (0.3199)
13229BN724
8.150 (0.3209)
Part number
Thickness
Items
Standard
Cylinder head gasket thickness
0.68 - 0.74 (0.0269 - 0.0291)
Head surface distortion
Less than 0.05 (0.002)
Normal cylinder head height “H”
127 (5.000)
E1BIA0063ZZ
Items
Standard
Valve head diameter “D”
mm (in)
Intake
33.38 - 33.62 (1.314 - 1.324)
Exhaust
28.88 - 29.12 (1.137 - 1.146)
Valve length “L”
mm (in)
Intake
100.74 - 101.16 (3.9661 - 3.9827)
Exhaust
100.54 - 100.96 (3.9583 - 3.9748)
Valve stem diameter “d”
mm (in)
Intake
5.969 - 5.985 (0.2350 - 0.2356)
Measuring point (X1) is 41 (1.61)
Exhaust
5.955 - 5.971 (0.2344 - 0.2351)
Measuring point (X1) is 31 (1.22)
Valve seat angle “
α
”
degree
45
°
00
′
(45.00
°
)
Valve margin “T”
mm (in)
1.0 (0.039)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст