Nissan Qashqai J11. Manual — part 976
SENSOR ROTOR
BRC-141
< REMOVAL AND INSTALLATION >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor
INFOID:0000000010428748
The front wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
Refer to
FAX-10, "Removal and Installation"
(2WD) or
FAX-49, "Removal and Installation"
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor
INFOID:0000000010428749
The rear wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
Refer to
BRC-141, "REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor"
BRC-142
< REMOVAL AND INSTALLATION >
[WITH ESP]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000010428750
Removal and Installation
INFOID:0000000010428751
REMOVAL
CAUTION:
• To remove brake tube, use a flare nut wrench to prevent flare nuts and brake tube from being dam-
aged.
• Do not remove actuator by holding harness.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Disconnect negative battery terminal. Refer to
PG-155, "Removal and Installation"
2.
Remove the cowl top cover and cowl top extension. Refer to
.
3.
Separate brake tubes from ABS actuator and electric unit (control unit). Refer to
.
4.
Remove the brake booster vacuum hose. Refer to
BR-29, "Removal and installation"
5.
Separate the brake booster vacuum tube and place aside. Refer to
6.
Disconnect the harness connector from the ABS actuator and electric unit (control unit).
7.
Remove ABS actuator and electric unit (control unit) bracket bolts and bushings.
8.
Remove ABS actuator and electric unit (control unit) from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• After work is completed, bleed air from brake tube. Refer to
BR-12, "Bleeding Brake System"
1.
ABS actuator and electric unit (control unit)
2.
Connector
3.
Bracket
A.
To front LH brake caliper
B.
To rear RH brake caliper
C. From master cylinder secondary side
D.
From master cylinder primary side
E.
To rear LH brake caliper
F.
To front RH brake caliper
AWFIA1079ZZ
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-143
< REMOVAL AND INSTALLATION >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Adjust the neutral position of steering angle sensor. Refer to
.
• Perform calibration of the decel G sensor. Refer to
.
CAUTION:
• To install, use flare nut crowfoot and torque wrench.
• Do not reuse the bushings.
• Replace the ABS actuator if it has been dropped or sustained an impact.
• Do not install actuator by holding harness.
• After installing harness connector in the ABS actuator and electric unit (control unit), make sure
connector is securely locked.
BRC-144
< REMOVAL AND INSTALLATION >
[WITH ESP]
VDC OFF SWITCH
VDC OFF SWITCH
Removal and Installation
INFOID:0000000010428752
REMOVAL
1.
Remove the instrument lower panel LH. Refer to
.
2.
Release pawls using suitable tool and remove the VDC OFF switch (2) from the upper switch carrier (1).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
ALFIA0414ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст