Nissan Qashqai J11. Manual — part 598
STR-34
< REMOVAL AND INSTALLATION >
STARTER MOTOR
R9M : Exploded View
INFOID:0000000010324196
R9M : Removal and Installation
INFOID:0000000010324197
REMOVAL
1.
Remove the battery and battery tray. Refer to
PG-155, "Removal and Installation"
2.
Remove the ECM (TCM) bracket and ECM (TCM). Refer to
TM-632, "Removal and Installation"
3.
Remove the harness bracket mounting nuts (
) and remove
the harness bracket (1) from the vehicle.
4.
Remove the air inlet tube. Refer to
5.
Remove the radiator hose (lower). Refer to
.
6.
Remove the alternator. Refer to
CHG-33, "R9M : Removal and Installation"
7.
Remove the oil level gauge and oil level gauge guide.
CAUTION:
Cover the openings to avoid entry of foreign materials.
8.
Remove the water hose. Refer to
.
1.
Starter motor
2.
“B” terminal harness
3.
“B” terminal nut
4.
“S” terminal nut
5.
“S” terminal harness
6.
Transmission housing
7.
Starter motor mounting bolt
: Vehicle front
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMBIA4245GB
JSDIA5410ZZ
STARTER MOTOR
STR-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
9.
Remove harness bracket (1).
10. Remove “B” terminal nut (A) and “B” terminal harness.
11. Remove “S” terminal nut (B) and “S” terminal harness.
12. Remove starter motor mounting bolts.
13. Remove starter motor (1) downward from the vehicle.
CAUTION:
For models with STOP/START SYSTEM, never erase the
starter operation counter except when replacing starter
motor.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Be careful to tighten “B” terminal nut to the specified torque.
• Erase the starter operation counter when the starter motor for models with STOP/START SYSTEM is
replaced. Refer to
• Replace the engine restart relay and the fuel pump relay when the starter motor models with STOP/
START SYSTEM is replaced.
: Vehicle front
JMBIA4601ZZ
: Vehicle front
JMBIA4602ZZ
STR-36
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Starter Motor
INFOID:0000000010201146
Engine
HR
K9K
Type
M000TD0371
M000TD0375
M000T46571
0 001 170 605
MITUBISHI make
BOSCH make
Reduction gear type
System voltage
[V]
12
No-load
Terminal voltage
[V]
11.5
—
Current
[A]
Less than 110
Less than 110
Less than 40
—
Revolution
[rpm]
More than 2,800
More than 2,800
More than 5,000
—
Minimum diameter of commutator
[mm (in)]
—
—
—
—
Minimum length of brush
[mm (in)]
—
—
—
—
Brush spring tension
[N (kg, lb)]
—
—
—
—
Clearance between bearing metal
and armature shaft
[mm (in)]
—
—
—
—
Clearance “L” between pinion front
edge and pinion stopper
[mm (in)]
—
—
—
—
Engine
R9M
MR20DD
MR16DDT
Type
0 001 170 607
S114 - 971
S116 - 001
BOSCH make
HITACHI make
Reduction gear type
System voltage
[V]
12
No-load
Terminal voltage
[V]
—
11
Current
[A]
—
Less than 110
Revolution
[rpm]
—
More than 3,300
More than 3,500
Minimum diameter of commutator
[mm (in)]
—
28.0 (1.102)
—
Minimum length of brush
[mm (in)]
—
10.5 (0.413)
—
Brush spring tension
[N (kg, lb)]
—
16.2 (1.65, 3.6)
—
Clearance between bearing metal and ar-
mature shaft
[mm (in)]
—
Less than 0.2
(0.008)
—
Clearance “L” between pinion front edge
and pinion stopper
[mm (in)]
—
0.3 - 2.5 (0.012 -
0.098)
—
CL-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
CL
A
B
CL
N
O
P
CONTENTS
CLUTCH
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Service Notice or Precautions for Clutch . . . . ..
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . ..
CLUTCH PEDAL . . . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ....
CLUTCH FLUID . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
Air Bleeding Procedure . . . . . . . . . . .....
REMOVAL AND INSTALLATION . . . ...
CLUTCH PEDAL . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
CLUTCH MASTER CYLINDER . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CLUTCH PIPING . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Hydraulic Layout . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION . ..
CSC (CONCENTRIC SLAVE CYLINDER) . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CLUTCH DISC AND CLUTCH COVER . . .
MR20DD . . . . . . . . . . . . . . . . . .
MR20DD : Exploded View . . . . . . . . . ...
MR20DD : Removal and Installation . . . . . ...
MR20DD : Inspection . . . . . . . . . . . ..
HRA2DDT . . . . . . . . . . . . . . . . ..
HRA2DDT : Exploded View . . . . . . . . . .
HRA2DDT : Removal and Installation . . . . . .
HRA2DDT : Inspection . . . . . . . . . . .
K9K . . . . . . . . . . . . . . . . . . .
K9K : Exploded View . . . . . . . . . . . ...
K9K : Removal and Installation . . . . . . . ...
K9K : Inspection . . . . . . . . . . . . . ..
R9M . . . . . . . . . . . . . . . . . . .
R9M : Exploded View . . . . . . . . . . . ..
R9M : Removal and Installation . . . . . . . ...
R9M : Inspection . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Clutch Control System . . . . . . . . . . . .
Clutch Pedal . . . . . . . . . . . . . . .
Clutch Disc . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст