Nissan Qashqai J11. Manual — part 566
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2.
Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
heard.
3.
After connecting, check that the connection is secured with following procedures.
• Visually confirm that the two tabs are connected to the connector.
• Pull (A) the tube and the connector to check that they are
securely connected.
4.
Reattach harness connector.
Inspection
INFOID:0000000010418981
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pres-
sure to fuel piping.
2.
Start engine and let it idle and make sure there are no fuel leaks at the fuel system connections.
JPBIA0140ZZ
FL-10
< REMOVAL AND INSTALLATION >
[HRA2DDT]
FUEL TANK
FUEL TANK
Exploded View
INFOID:0000000010418985
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010418986
REMOVAL
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
1.
Perform the steps 1 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL
PUMP ASSEMBLY”. Refer to
FL-6, "Removal and Installation"
.
2.
Drain fuel from fuel tank if necessary. Refer to
FL-6, "Removal and Installation"
.
CAUTION:
• Fuel tank will become unstable whilst removing. Fuel should be drained from tank prior to
removal to reduce this effect.
• Situate vehicle on a flat and solid surface.
3.
Remove main muffler. Refer to
.
4.
Remove vent hose from filler tube.
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Clamp
5.
Fuel filler hose
6.
Clamp
7.
Clamp
8.
Vent hose
9.
EVAP hose
10. Fuel tank
11.
Fuel tank band (RH)
12. Fuel tank band (LH)
E1BIA1121GB
FUEL TANK
FL-11
< REMOVAL AND INSTALLATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
5.
Remove fuel filler hose from fuel tank.
CAUTION:
• Do not remove fuel filler hose from fuel filler tube to prevent interference with suspension when
installing.
• If removal of fuel filler hose from fuel filler tube is necessary use mating marks to ensure correct
orientation.
6.
Disconnect EVAP hose.
• Remove quick connector in the following procedures.
- Hold the sides of quick connector, press tabs and disconnect EVAP hose.
- If quick connector sticks to tube, push and pull quick connectors several times until they start to move.
Then disconnect them by pulling.
CAUTION:
• Quick connector can be disconnected when the tabs (1)
are depressed completely. Never twist it more than neces-
sary.
• Never use any tools to disconnected quick connector.
• Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Never bend or twist resin tube during installation and dis-
connection.
• Never insert plug, preventing damage to O–ring in quick
connector.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags or something similar.
E1BIA1192ZZ
A
: Connection (cross-section)
B
: Disconnection (cross-section)
C
: Quick connector
D
: Hard tube
E1BIA1190ZZ
FL-12
< REMOVAL AND INSTALLATION >
[HRA2DDT]
FUEL TANK
7.
Support center of fuel tank (1) with transmission jack (A) and
piece of wood (B).
CAUTION:
• Make sure the tank bottom surface is supported well
enough to prevent an unstable condition when lowering
the tank.
• Make sure to hold it securely as tank surface may not be
flat.
8.
Remove fuel tank band (RH and LH).
9.
Lower transmission jack carefully to remove fuel tank while holding it by hand.
CAUTION:
Make sure to avoid any interference with surrounding component that may cause damage.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Make sure hose clamps and hoses clips are not secured on top of the filler tube bulges.
• Make sure all quick connectors and their mating part are free of foreign matter, check for damage.
• Ensure the tank bands are correctly assembled as per their identification marks "L" and "R".
• Make sure that the torques of the mounting bolts are correct as per exploded view. Refer to
.
• Make sure that when installing the connectors, the confirmation click sound is heard. Pull back on
the connector to ensure proper engagement.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel filler tube.
• Tighten fuel filler hose clamp so that the remaining length of screw thread becomes to the following.
EVAP Hose
1.
Check connections for damage or foreign material.
2.
Align the matching side connection part with the center of shaft,
and insert connector straight until it clicks.
3.
After connecting, pull out quick connector and centralized under-
floor piping by hand. Make sure connections are secure.
Inspection
INFOID:0000000010418987
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
PBIC3792E
: 35 mm (1.38 in)
Fuel filler tube side
: 7 - 11 mm (0.28 - 0.43 in)
Fuel tank side
: 5 - 9 mm (0.20 - 0.35 in)
PBIC1653E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст