Nissan Qashqai J11. Manual — part 825
DLN-216
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DIFFERENTIAL ASSEMBLY
4.
Align the lock pin holes on differential case with shaft, and install
pinion mate shaft.
5.
Measure side gear end play following the procedure below, and select the appropriate side gear thrust
washers.
a.
Place differential case straight up so that side gear to be mea-
sured comes upward.
b.
Using thickness gauges, measure the clearance between side
gear back and differential case at 3 different positions, while
rotating side gear. Average the 3 readings, and then measure
the clearance. (Measure the clearance of the other side as well.)
CAUTION:
To prevent side gear from tilting, insert thickness gauges
with the same thickness from both sides.
c.
If the back clearance is outside the specification, use a thicker/
thinner side gear thrust washer to adjust.
CAUTION:
Select a side gear thrust washer for right and left individu-
ally.
SDIA0037J
PDIA0460E
Standard
Side gear back clearance
: Refer to
When the back clearance is large:
Use a thicker thrust washer.
When the back clearance is small:
Use a thinner thrust washer.
SDIA0583E
DIFFERENTIAL ASSEMBLY
DLN-217
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
6.
Drive a lock pin into pinion mate shaft, using the pin punch
(commercial service tool).
CAUTION:
Never reuse lock pin.
7.
Press side bearing inner races to differential case, using the drift
(commercial service tool).
CAUTION:
Never reuse side bearing inner races.
8.
Apply locking sealant into the thread hole of drive gear.
CAUTION:
The drive gear back and threaded holes shall be cleaned
and decreased sufficiently.
9.
Install drive gear to the differential case, and then tighten to the
specified torque.
10. Apply gear oil to side bearings, and install new side bearing
adjusting shims (2 pieces for one side) with the same thickness
as the ones installed prior to disassembly or re-install the old
ones, with side bearing outer race to differential case.
If side bearing adjusting shims have been already selected, use
them.
CAUTION:
Never reuse side bearing outer race.
11. Set the drifts (commercial service tool) to the right and left side
bearing adjusting shims individually. Compress differential case
assembly and side bearing to install gear carrier assembly to dif-
ferential case assembly.
CAUTION:
• The drift shall be placed on the center of the adjusting
shims.
• The pressure shall be as low as possible to install differ-
ential assembly into gear carrier assembly. The maximum
pressure shall be 10 kN (1 ton, 1.0 Imp ton).
• If the adjusting shims are installed by tapping, the gear
carrier may be damaged. Avoid tapping.
PDIA0062E
PDIA0052E
SPD554
PDIA0466E
PDIA0064E
DLN-218
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DIFFERENTIAL ASSEMBLY
12. Install dummy cover set, check and adjust drive gear runout, tooth contact, backlash, and total preload
13. Remove dummy cover set.
14. Apply liquid gasket to mating surface of rear cover. Overlap both
ends of the bead for at least 3 mm (0.12 in).
CAUTION:
Remove old gasket adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adhering
to the mounting surfaces.
15. Set the drifts (commercial service tool) to the right and left side
bearing adjusting shims individually. Compress differential case
assembly and side bearing to install rear cover.
CAUTION:
• The drift shall be placed on the center of the adjusting
shims.
• The pressure shall be as low as possible to install the rear
cover. The maximum pressure shall be 10 kN (1 ton, 1.0
Imp ton).
• If rear cover is forced in by tapping, rear cover may be
damaged by adjusting shims. Avoid tapping.
16. Tighten rear cover mounting bolts to the specified torque.
17. Using the drift (SST: KV38100200), drive side oil seals until it
becomes flush with the carrier end.
CAUTION:
• Never reuse oil seals.
• When installing, do not incline oil seals.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
18. Check total preload torque. Refer to
.
Inspection After Disassembly
INFOID:0000000010288417
Clean up the disassembled parts. Then, inspect if the parts are worn or damaged. If so, follow the measures
below.
PDIA0447E
PDIA0065E
PDIA0448E
Content
Conditions and Measures
Hypoid gear
• If the gear teeth do not mesh or line-up correctly, determine the cause and adjust or replace as nec-
essary.
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new
drive gear and drive pinion as a set.
Bearing
If any chipped (by friction), pitted, worn, rusted or scratched mark, or unusual noise from the bearing is
observed, replace as a bearing assembly (as a new set).
Side gear and Pinion mate
gear
• If any cracks or damage on the surface of the tooth is found, replace.
• If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
Side gear thrust washer and
pinion mate thrust washer
If it is chipped (by friction), damaged, or unusually worn, replace.
Differential case
If any wear or crack on the contact sides of the differential case is found, replace.
Companion flange
If any chipped mark (about 0.1 mm, 0.004 in) or other damage on the contact sides of the lips of the com-
panion flange is found, replace.
DRIVE PINION
DLN-219
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DRIVE PINION
Exploded View
INFOID:0000000010288418
R9M
1.
Filler plug
2.
Gasket
3.
Drain plug
4.
Rear cover
5.
Side oil seal
6.
Side bearing adjusting shim
7.
Side bearing
8.
Drive gear
9.
Differential case
10. Pinion mate thrust washer
11.
Pinion mate gear
12. Pinion mate shaft
13. Lock pin
14. Side gear thrust washer
15. Side gear
16. Drive pinion
17. Pinion rear bearing
18. Drive pinion adjusting shim
19. Collapsible spacer
20. Gear carrier
21. Pinion front bearing
22. Drive pinion nut
23. Center oil seal
24. 4WD solenoid harness
25. Electric controlled coupling
26. Coupling cover
27. Reamer bolt
28. Connector bracket
29. Front oil seal
30. Companion flange
31. Companion flange lock nut
A: Oil seal lip
B: Screw hole
: Apply gear oil.
: Apply anti-corrosive oil.
: Apply Genuine Liquid Gasket, Three Bond 1217 or equivalent.
: Apply Genuine Medium Strength Thread Locking Sealant, Three Bond 1322B or equivalent.
Refer to
for symbols not described on the above.
JPDID0006GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст