Nissan Qashqai J11. Manual — part 824
DLN-212
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
ELECTRIC CONTROLLED COUPLING
Adjustment
INFOID:0000000010288412
COMPANION FLANGE RUNOUT
1.
Fit a dial indicator onto the companion flange face (inner side of
the rear propeller shaft mounting bolt holes).
2.
Rotate companion flange to check for runout.
3.
Fit a test indicator to the inner side of companion flange (socket
diameter).
4.
Rotate companion flange to check for runout.
5.
If the runout value is outside the runout limit, follow the procedure below to adjust.
a.
Check for runout while changing the phase between companion flange and drive pinion by 90
°
step, and
search for the position where the runout is the minimum.
b.
If the runout value is still outside of the limit after the phase has been changed, replace companion flange.
c.
If the runout value is still outside of the limit after companion flange has been replaced, possible cause will
be an assembly malfunction of drive pinion and electric controlled coupling, malfunctioning coupling bear-
ing, or malfunctioning of electric controlled coupling.
Inspection After Disassembly
INFOID:0000000010288413
Clean up the disassembled parts. Then, inspect if the parts are worn or damaged. If so, follow the measures
below.
Limit
Companion flange runout
: Refer to
.
Limit
Companion flange runout
: Refer to
.
PDIA0439E
Content
Conditions and Measures
Hypoid gear
• If the gear teeth do not mesh or line-up correctly, determine the cause and adjust or replace as nec-
essary.
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new
drive gear and drive pinion as a set.
Bearing
If any chipped (by friction), pitted, worn, rusted or scratched mark, or unusual noise from the bearing is
observed, replace as a bearing assembly (as a new set).
Side gear and Pinion mate
gear
• If any cracks or damage on the surface of the tooth is found, replace.
• If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
Side gear thrust washer and
pinion mate thrust washer
If it is chipped (by friction), damaged, or unusually worn, replace.
Differential case
If any wear or crack on the contact sides of the differential case is found, replace.
Companion flange
If any chipped mark (about 0.1 mm, 0.004 in) or other damage on the contact sides of the lips of the com-
panion flange is found, replace.
DIFFERENTIAL ASSEMBLY
DLN-213
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DIFFERENTIAL ASSEMBLY
Exploded View
INFOID:0000000010288414
R9M
1.
Filler plug
2.
Gasket
3.
Drain plug
4.
Rear cover
5.
Side oil seal
6.
Side bearing adjusting shim
7.
Side bearing
8.
Drive gear
9.
Differential case
10. Pinion mate thrust washer
11.
Pinion mate gear
12. Pinion mate shaft
13. Lock pin
14. Side gear thrust washer
15. Side gear
16. Drive pinion
17. Pinion rear bearing
18. Drive pinion adjusting shim
19. Collapsible spacer
20. Gear carrier
21. Pinion front bearing
22. Drive pinion nut
23. Center oil seal
24. 4WD solenoid harness
25. Electric controlled coupling
26. Coupling cover
27. Reamer bolt
28. Connector bracket
29. Front oil seal
30. Companion flange
31. Companion flange lock nut
A: Oil seal lip
B: Screw hole
: Apply gear oil.
: Apply anti-corrosive oil.
: Apply Genuine Liquid Gasket, Three Bond 1217 or equivalent.
: Apply Genuine Medium Strength Thread Locking Sealant, Three Bond 1322B or equivalent.
Refer to
for symbols not described on the above.
JPDID0006GB
DLN-214
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DIFFERENTIAL ASSEMBLY
Disassembly
INFOID:0000000010288415
1.
Remove side oil seals, using flat-bladed screwdriver.
CAUTION:
Be careful not to damage gear carrier and rear cover.
2.
Remove rear cover mounting bolts.
3.
Set drifts (commercial service tool) to the right and left side bear-
ing adjusting shims individually. Press differential case assembly
with side bearing to remove gear carrier assembly and rear
cover assembly.
CAUTION:
The pressure shall be as low as possible to remove gear
carrier assembly and rear cover assembly. The maximum
pressure shall be 10 kN (1 ton, 1.0 Imp ton).
NOTE:
Differential case assembly, side bearings, and adjusting shims
are compressed and integrated in gear carrier and rear cover.
4.
Remove drain plug and filler plug.
5.
Remove side bearing adjusting shims and side bearing outer races.
CAUTION:
Mark the side bearing adjusting shims so that the original mounting positions (right/left) can be
identified later.
6.
Remove drive gear mounting bolts and then remove drive gear
from differential case.
7.
Remove side bearing inner races, using pullers and the drift
(SST: ST33052000).
PDG0216D
PDIA0065E
PDIA0446E
PDIA0459E
DIFFERENTIAL ASSEMBLY
DLN-215
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
8.
Pull the lock pin out of pinion mate shaft, using the pin punch
(commercial service tool).
9.
Remove pinion mate shaft, pinion mate gears, pinion mate
thrust washers, side gears, side gear thrust washers from differ-
ential case.
Assembly
INFOID:0000000010288416
1.
Install side gear thrust washers with the same thickness as the
ones installed prior to disassembly or reinstall the old ones on
the side gears.
2.
Install side gears and side gear thrust washers into differential
case.
3.
Align 2 pinion mate gears in diagonally opposite positions, then
rotate and install them into differential case after installing pinion
mate thrust washer to pinion mate gear.
PDIA0062E
SDIA0032J
SDIA0193J
SDIA0036J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст