Nissan Qashqai J11. Manual — part 861
REAR SHOCK ABSORBER
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000010297259
FOR 2WD EUROPE (HT)
FOR 2WD GOM AND 4WD (TC)
E1EIA0116GB
1.
Rear suspension beam
2.
Rear shock absorber
Refer to
for symbols in the figure.
E1EIA0120GB
1.
Rear suspension member
2.
Upper rubber seat
3.
Coil spring
4.
Lower rubber seat
5.
Rubber washer (LH/RH)
6.
Rear suspension arm
7.
Rear shock absorber
: Front
Refer to
for symbols in the figure.
RSU-10
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
Removal and Installation
INFOID:0000000010297260
REMOVAL
1.
Remove tires from vehicle.
2.
Set suitable jack under suspension arm to relieve the coil spring tension.
3.
Remove shock absorber.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000010297261
INSPECTION AFTER REMOVAL
• Check shock absorber for deformation, cracks, damage. Replace it if necessary.
• Check welded and sealed areas for oil leakage. Replace it if necessary.
INSPECTION AFTER INSTALLION
1.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
2.
Adjust neutral position of steering angle sensor. Refer to
.
Disposal
INFOID:0000000010297262
1.
Set shock absorber horizontally with the piston rod fully extended.
2.
Drill 2 - 3 mm (0.08 - 0.12 in) hole at the position (
z
) from the top
as shown to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in the direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A : approximately 20 mm (0.79 in)
JPEIA0161ZZ
SUSPENSION ARM
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SUSPENSION ARM
Exploded View
INFOID:0000000010297263
FOR 2WD EUROPE (HT)
FOR 2WD GOM AND 4WD (TC)
Removal and Installation
INFOID:0000000010480373
REMOVAL
1.
Remove the wheel hub and bearing. Refer to
RAX-12, "Removal and Installation"
.
2.
RSU-7, "Removal and Installation"
.
E1EIA0118GB
1.
Rear suspension beam
2.
Rear suspension arm bracket
Refer to
for symbols in the figure.
E1EIA0121GB
1.
Rear suspension arm
2.
Rubber washer (LH/RH)
3.
Rear suspension arm bracket
4.
Rear suspension arm stay
: Front
Refer to
for symbols in the figure.
RSU-12
< REMOVAL AND INSTALLATION >
SUSPENSION ARM
3.
Separate the brake tube and hose from the rear suspension arm.
(LHD),
4.
Remove the nut, bolt, rubber washer (LH/RH).
5.
Remove rear suspension arm from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Align the matching marks made during removal when reusing the disc brake rotor.
• After installation, perform the air bleeding. Refer to
BR-12, "Bleeding Brake System"
.
• Perform final tightening of rear suspension member at its installation position under unladen conditions with
tires on level ground.
• Perform the inspection after installation. Refer to
.
Inspection
INFOID:0000000010297265
INSPECTION AFTER REMOVAL
Visual Inspection
Check suspension arm and bushing for deformation, cracks or damage. Replace it if necessary.
INSPECTION AFTRE INSTALLATION
1.
Adjust parking brake operation (stroke). Refer to
2.
Check wheel alignment. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст