Nissan Qashqai J11. Manual — part 862
LOWER LINK
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
LOWER LINK
Exploded View
INFOID:0000000010297266
FOR 2WD GOM AND 4WD
Removal and Installation
INFOID:0000000010480374
REMOVAL
1.
Remove wheel and tire using power tool. Refer to
2.
Remove connecting rod. Refer to
3.
Remove rear height sensor (if equipped). Refer to
EXL-171, "Removal and Installation"
4.
Set suitable jack under rear suspension arm to relieve the coil spring tension.
5.
Remove lower link, nut, and bolt from rear suspension arm with power tool.
6.
Remove lower link, nut, washer, and bolt from rear suspension member with power tool.
7.
Remove lower link protector (if necessary).
8.
Perform the inspection after removal. Refer to
INSTALLATION
Installation is in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position under unladen conditions
with tires on level ground.
• After installation, perform headlamp initialization. Refer to
.
• Adjust the neutral position of the steering angle sensor. Refer to
• Perform the inspection after installation. Refer to
.
E1EIA0122GB
1.
Rear suspension member
2.
Lower link
3.
Lower link deflector
4.
Rubber washer (RLH/RH)
5.
Rear suspension arm
: Front
Refer to
for symbols in the figure.
RSU-14
< REMOVAL AND INSTALLATION >
LOWER LINK
Inspection
INFOID:0000000010297268
INSPECTION AFTER REMOVAL
Check lower link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
2.
Adjust neutral position of steering angle sensor. Refer to
.
UPPER LINK
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UPPER LINK
Exploded View
INFOID:0000000010297269
FOR 2WD GOM AND 4WD
Removal and Installation
INFOID:0000000010297270
REMOVAL
1.
Remove tires from vehicle.
2.
Set suitable jack under suspension arm to relieve the coil spring tension.
3.
Remove wheel sensor harness from suspension arm.
4.
Remove upper link from suspension arm.
5.
Remove upper link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000010297271
INSPECTION AFTER REMOVAL
Check upper link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
2.
Adjust neutral position of steering angle sensor. Refer to
.
AWEIA0356ZZ
1.
Rear suspension member
2.
Upper link
3.
Rubber washer (LH/RH)
4.
Rear suspension arm
: Front
Refer to
for symbols in the figure.
RSU-16
< REMOVAL AND INSTALLATION >
REAR STABILIZER
REAR STABILIZER
Exploded View
INFOID:0000000010297272
FOR 2WD GOM AND 4WD
Removal and Installation
INFOID:0000000010297273
REMOVAL
1.
Disconnect rear stabilizer links from rear stabilizer bar.
2.
Remove nuts on rear stabilizer clamp.
3.
Remove rear stabilizer bar from rear suspension member.
4.
Remove rear stabilizer bushings from rear stabilizer bar.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000010297274
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer link, stabilizer bushing and stabilizer clamp for deformation, cracks or damage.
Replace it if necessary.
E1EIA0123GB
1.
Rear stabilizer bar
2.
Connecting rod (RH)
3.
Rear stabilizer bar bushing
4.
Rear stabilizer bar clamp
5.
Connecting rod (LH)
: Front
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст