Nissan Maxima. Manual — part 553
EM-100
< REMOVAL AND INSTALLATION >
ENGINE MOUNT
ENGINE MOUNT
ENGINE MOUNT (FRONT)
ENGINE MOUNT (FRONT) : Removal and Installation
INFOID:0000000009466049
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Always work safely.
• Do not start work until the engine and exhaust system are cooled completely.
CAUTION:
Do not damage or spill oil on the engine mount insulator (front).
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the air cleaner assembly, front air duct, and air duct hose and resonator tube assembly. Refer to
EM-24, "Removal and Installation"
2. Remove the battery and battery tray assembly. Refer to
PG-68, "Removal and Installation (Battery Tray)"
.
3. Remove the engine under cover. Refer to
.
4. Remove the fender protector side covers (RH/LH). Refer to
EXT-24, "Removal and Installation"
.
5. Remove the radiator. Refer to
CO-14, "Removal and Installation"
.
6. Remove the fan shroud and motor assembly. Refer to
CO-16, "Removal and Installation"
7. Remove the exhaust manifold heat shield (LH). Refer to
EM-31, "Removal and Installation (LH)"
8. Support the engine (1) and transaxle (2) using a suitable jack (A)
as shown.
CAUTION:
• Position a suitable jack under the engine and transaxle
assembly as shown.
• Do not damage the front exhaust tube or transaxle oil pan
with the jack.
9. Disconnect the engine mount insulator (front) vacuum hose.
10. Remove the engine mount insulator (front) nut (A).
ALBIA0894GB
AWBIA1241GB
ENGINE MOUNT
EM-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
11. Loosen the engine mount bracket (front) bolts in the reverse
order shown.
12. Remove the engine mount bracket (front).
13. Remove the engine mount insulator (front) bolts in the reverse
order as shown.
14. Remove the engine mount insulator (front).
INSTALLATION
1. Install the engine mount insulator (front).
: Engine front
JPBIA1731ZZ
: Vehicle front
JPBIA1735ZZ
AWBIA1242GB
AWBIA1242GB
EM-102
< REMOVAL AND INSTALLATION >
ENGINE MOUNT
2. Install the engine mount insulator (front) bolts and tighten to
specification in the order shown.
CAUTION:
Check engine mount insulator (front) is seated properly
before tightening.
3. Install the engine mount bracket (front) to the engine block.
4. Tighten the engine mount bracket (front) bolts to specification in
the order shown.
5. Install the engine mount insulator (front) nut (A) and tighten to
specification.
6. Installation of the remaining components is in the reverse order of removal.
: Front
Engine mount insulator (front)
bolts
: 43 N·m (4.4 kg-m,
32 ft-lb)
JPBIA1735ZZ
: Engine front
Engine mount bracket (front)
bolts
: 40 N·m (4.1 kg-m,
30 ft-lb)
JPBIA1731ZZ
Engine mount insulator (front)
nut
: 103 N·m (11 kg-m,
76 ft-lb)
AWBIA1241GB
ENGINE ASSEMBLY
EM-103
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Removal and Installation
INFOID:0000000009466050
WARNING:
• Place chocks at front and back of rear wheels.
• For engines not equipped with engine slingers, attach proper slingers and bolts as described in the
NISSAN Parts Catalog.
CAUTION:
• Do not start working until exhaust system and coolant are cool.
1.
Upper torque rod
2.
Rear torque rod
3.
Engine mounting insulator (RH)
4.
Engine mounting bracket (front) 5.
Engine mounting insulator (front)
6.
Engine mounting bracket (RH)
7.
Rear torque rod bracket
8.
Engine mounting insulator (LH)
9.
Engine mounting insulator (rear)
10. Engine mounting bracket (rear)
AWBIA1644ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст