Nissan Maxima. Manual — part 671
FRONT SUSPENSION ASSEMBLY
FSU-13
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
UNIT REMOVAL AND INSTALLATION
FRONT SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000009466799
AWEIA0269ZZ
FSU-14
< UNIT REMOVAL AND INSTALLATION >
FRONT SUSPENSION ASSEMBLY
Removal and Installation
INFOID:0000000009466800
REMOVAL
• Engine, transmission and suspension member must be removed as an assembly. Refer to
• Once removed as an assembly, lift engine and transmission off suspension member using suitable tool.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, perform final tightening of each part under unladen conditions with tires on ground. Refer to
• Check wheel alignment. Refer to
FSU-6, "Inspection and Adjustment"
.
1.
Front stabilizer
2.
Stabilizer clamp
3.
Stabilizer bushing
4.
Stabilizer connecting rod
5.
Front mount bracket
6.
Rear mount bracket
7.
Member insulator
8.
Member pin stay
9.
Transverse link
10. Steering stopper bracket
11. Stopper bolt cap
12. Steering stopper bolt
13. Steering knuckle
14. Front suspension member
15. Front suspension strut
16. Front spring lower rubber seat
17. Front spring
18. Strut mount bearing
19. Bound bumper
20. Strut mount insulator
Front
FRONT COIL SPRING AND STRUT
FSU-15
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT COIL SPRING AND STRUT
Disassembly and Assembly
INFOID:0000000009466801
DISASSEMBLY
1. Install Tool (A) to the front coil spring and strut.
CAUTION:
When installing Tool (A), wrap a shop cloth around the front
coil spring and strut to protect the parts from damage.
2. Secure Tool (A) in a vise.
3. Slightly loosen the piston rod lock nut.
WARNING:
Do not remove piston rod lock nut completely. If the piston rod lock nut is removed completely,
the front spring can jump out and may cause serious damage or injury.
4. Compress the front spring using a spring compressor (commer-
cial service tool).
WARNING:
Make sure that the pawls of the two spring compressors are
firmly hooked on the front spring. The spring compressors
must be tightened alternately so as not to tilt the front
spring.
5. Make sure the front spring is free between the strut mount bearing and the front spring lower rubber seat.
Remove the piston rod lock nut.
6. Remove the strut mount insulator, the bound bumper, and the strut mount bearing.
7. Remove the bound bumper from the strut mount insulator.
8. Gradually release the spring compressor (commercial service tool) and remove the front spring.
9. Remove the front spring lower rubber seat.
ASSEMBLY
1. Install the front spring lower rubber seat (2) to the front suspen-
sion strut.
2. Compress the front spring (1) using a spring compressor (com-
mercial service tool), and install the front spring to the front sus-
pension strut.
WARNING:
Make sure that the pawls of the two spring compressors are
firmly hooked on the front spring. The spring compressors
must be tightened alternately so as not to tilt the front
spring.
CAUTION:
Face the tube side of the coil spring downward. Align the
front spring lower end (A) to the front spring lower rubber seat as shown.
3. Install the bound bumper to the strut mount insulator.
Tool number
: ST35652000 (
—
)
AWEIA0262ZZ
SEIA0297E
AWEIA0271ZZ
FSU-16
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT COIL SPRING AND STRUT
CAUTION:
• Be sure to install the bound bumper to the strut mount insulator securely.
• When installing the bound bumper, use soapy water. Do not use machine oil or other lubricants.
4. Install the strut mount bearing, the bound bumper, and the strut mount insulator to the strut. Temporarily
install the piston rod lock nut.
CAUTION:
Do not reuse the piston rod lock nut.
5. Be sure tab (A) on strut mount insulator is positioned as shown.
: Front
6. Be sure the front spring is properly set in the front spring lower rubber seat. Gradually release the spring
compressor (commercial service tool).
CAUTION:
Be sure the strut mount bearing is properly aligned to the strut mount insulator and to the front
spring.
7. Tighten the piston rod lock nut to the specified torque.
8. Remove Tool (A) from the vise.
9. Remove Tool (A) from the front coil spring and strut.
Inspection
INFOID:0000000009466802
INSPECTION AFTER DISASSEMBLY
Front Suspension Strut
• Check the front suspension strut for deformation, cracks, and damage. Replace if necessary.
• Check the piston rod for damage, uneven wear, and distortion. Replace if necessary.
• Check the welded and sealed areas for oil leakage. Replace if necessary.
Insulator and Rubber Parts
ALEIA0060ZZ
Tool number
: ST35652000 (
—
)
AWEIA0262ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст