Nissan Maxima. Manual — part 875
MWI
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
MWI-115
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000010049624
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000010049625
1.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair harness or connector.
2.
CHECK WASHER FLUID LEVEL SWITCH UNIT
Perform a unit check for the washer fluid level switch. Refer to
MWI-46, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-122, "Removal and Installation"
NO
>> Replace washer fluid level switch.
MWI-116
< SYMPTOM DIAGNOSIS >
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000010049626
• The door ajar warning is displayed even though all of the doors and the trunk are closed.
• The door ajar warning is not displayed even though a door or the trunk is ajar.
Diagnosis Procedure
INFOID:0000000010049627
1.
CHECK BCM INPUT SIGNAL
Connect CONSULT and check the BCM input signals. Refer to
DLK-67, "Component Function Check"
switch) and
DLK-88, "Component Function Check"
(Trunk lamp switch and truck release solenoid).
Are the inspection results normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” on CONSULT.
2. Monitor “DOOR W/L” and “TRUNK/GLAS-H” of “DATA MONITOR” while opening and closing doors and
trunk.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-122, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
3.
CHECK DOOR SWITCH SIGNAL CIRCUIT
Check the door switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair harness or connector.
4.
CHECK DOOR SWITCH UNIT
Perform a unit check for the door switch. Refer to
DLK-69, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace door switch.
5.
CHECK TRUNK LAMP SWITCH AND TRUNK RELEASE SOLENOID SIGNAL CIRCUIT
Check the trunk lamp switch and trunk release solenoid signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair harness or connector.
6.
CHECK TRUNK LAMP SWITCH AND TRUNK RELEASE SOLENOID UNIT
Perform a unit check for the trunk lamp switch and trunk release solenoid. Refer to
.
“DOOR W/L”
Door open
: ON
Door closed
: OFF
“TRUNK/GLAS-H”
Trunk open
: ON
Trunk closed
: OFF
MWI
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
MWI-117
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-122, "Removal and Installation"
NO
>> Replace trunk lamp switch and trunk release solenoid.
MWI-118
< SYMPTOM DIAGNOSIS >
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000010049628
• The displayed ambient air temperature is higher than the actual temperature.
• The displayed ambient air temperature is lower than the actual temperature.
Diagnosis Procedure
INFOID:0000000010049629
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” on CONSULT.
2. Using “OUTSIDE TEMP” on DATA MONITOR, compare the value of DATA MONITOR with the actual
ambient temperature. DATA MONITOR value and actual ambient temperature should be close.
Does the data monitor value approximately match the actual ambient temperature?
YES
>> Replace combination meter. Refer to
MWI-122, "Removal and Installation"
NO
>> Refer to
(with color display) or
HAC-136, "Diagnosis Procedure"
(with monochrome display).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст