Nissan Maxima. Manual — part 646
EXL-326
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009465397
Removal and Installation
INFOID:0000000009465398
REAR COMBINATION LAMP
Removal
1. Remove the trunk side finisher. Refer to
2. Remove the rear combination lamp nuts.
3. Pull the rear combination lamp toward the rear of the vehicle to remove it.
4. Disconnect the harness connector from the rear combination lamp.
Installation
Installation is in the reverse order of removal.
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off, a burn injury may result.
CAUTION:
• Do not touch bulb glass with your hand or keep other grease and oily substances away from bulb
glass.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement is integral with rear combination lamp. Refer to
REAR SIDE MARKER LAMP BULB
Removal
1. Remove the rear combination lamp. Refer to
2. Rotate the rear side marker lamp socket counterclockwise and unlock from rear combination lamp.
3. Remove the bulb from the rear side marker lamp socket.
Installation
Installation is in the reverse order of removal.
REAR TURN SIGNAL LAMP BULB
1.
Slide clip
2.
Grommets
3.
Rear combination lamp
ALLIA0902ZZ
REAR COMBINATION LAMP
EXL-327
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal
1. Remove the rear combination lamp. Refer to
2. Rotate the rear turn signal lamp socket counterclockwise and unlock from rear combination lamp.
3. Remove the bulb from the rear turn signal lamp socket.
Installation
Installation is in the reverse order of removal.
BACK-UP LAMP BULB
Removal
1. Remove the rear combination lamp. Refer to
2. Rotate the back-up lamp socket counterclockwise and unlock from rear combination lamp.
3. Remove the bulb from the back-up lamp socket.
Installation
Installation is in the reverse order of removal.
EXL-328
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009465399
Removal and Installation
INFOID:0000000009465400
REMOVAL
1. Slide the high-mounted stop lamp rearward on the parcel shelf to give clearance to the front locking tabs.
2. Lift the front of the high-mounted stop lamp up and slide it for-
ward to give clearance to the rear locking tabs.
3. Disconnect the harness connector from the high-mounted stop
lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
High-mounted stop lamp cover
2.
High-mounted stop lamp bulb
AWLIA1815ZZ
LKIA0063E
LICENSE PLATE LAMP
EXL-329
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009465401
Removal and Installation
INFOID:0000000009465402
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to
EXT-31, "Removal and Installation"
.
2. Position trunk lid finisher aside. Refer to
3. Remove the license plate lamp screw and remove the license
plate lamp.
Installation
Installation is in the reverse order of removal.
LICENSE PLATE LAMP BULB
Removal
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off, a burn injury may result.
CAUTION:
• Do not touch bulb glass with your hand or keep other grease and oily substances away from bulb
glass.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
1. Position trunk lid finisher aside. Refer to
1.
License plate lamp
ALLIA0906ZZ
PKIA0059E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст